Home Repair
How to Remove a Sink Drain (Bathroom and Kitchen)
Remove a bathroom pop-up drain or a kitchen basket strainer step by step: stopper, pivot rod, P-trap, locknut and flange — plus how to reinstall it without leaks.
Sink drains come out for three reasons: the old one leaks around the flange, the finish is corroded, or you're replacing the faucet and want the drain to match. Either way, the job is mostly unscrewing things in the right order — and knowing what holds the drain in place before you start pulling.
A bathroom sink usually has a pop-up drain with a stopper, a pivot rod and a locknut. A kitchen sink usually has a basket strainer held by a big locknut or a snap ring. This guide covers both, with separate steps marked "Bathroom" and "Kitchen". Skip the ones that don't apply to you.
Which drain do I have?
| Look for | Drain type | Held in by |
|---|---|---|
| Stopper raised and lowered by a rod behind the faucet | Bathroom pop-up drain | Large locknut on the drain body; pivot rod holds the stopper |
| Push-button stopper (click-clack), no rod | Bathroom push-to-seal drain | Large locknut; the stopper usually unscrews from the top |
| Wide strainer basket in a kitchen sink | Kitchen basket strainer | Large locknut, or a snap ring with three screws |
| A garbage disposal under the sink | Disposal flange | Disposal mounting ring — see how to replace a garbage disposal |
Getting the right replacement
Bring the old drain to the store or measure it: bathroom drains differ in tailpiece length, whether they have an overflow opening, and how the stopper works. A drain removal tool makes quick work of stubborn flanges, and our roundups of bathroom sink drains and kitchen sink strainers cover finishes and sealing styles. Follow the manufacturer's instructions for the order of gaskets and washers.
Related jobs
If the sink is just slow rather than leaking, try unclogging the drain before you take anything apart. A drip from the spout is the faucet, not the drain — see how to fix a leaky faucet. And if the toilet is backing up too, here's how to unclog a toilet.
Step by step
- 1
Clear the cabinet and put a bucket under the trap
Empty the space under the sink and lay down a towel. Set a bucket directly under the P-trap — the U-shaped pipe — because it holds water. Close the faucet so nobody turns it on mid-job.
- 2
Disconnect the P-trap
Loosen the two slip nuts on the P-trap by hand or with channel-lock pliers, then lower the trap into the bucket. Pour out the water and set the trap aside. Stuff a rag loosely into the wall pipe to block sewer gas.
- 3
Bathroom: remove the pivot rod and stopper
Behind the drain pipe, find the horizontal pivot rod connected to the lift rod by a metal strap (the clevis). Squeeze the spring clip off the rod, slide the rod out of the clevis, then unscrew the pivot nut and pull the rod out of the drain body. Now lift the stopper straight out of the drain from above.
- 4
Bathroom: loosen the drain body locknut
Under the sink, unscrew the large locknut on the drain body (the tailpiece) with pliers, turning counterclockwise as seen from below. If it spins the whole drain, have a helper hold the flange from above with a drain key or with needle-nose pliers spread inside the crosspiece and a screwdriver through the handles for leverage.
- 5
Bathroom: push out the flange
With the locknut, friction washer and rubber gasket off, push the drain body up from below. The flange will lift out of the sink, usually with old putty attached. If it's stuck, unscrew the flange from the drain body from above using the drain key while you hold the body steady below.
- 6
Kitchen: disconnect the tailpiece from the strainer
For a kitchen sink, loosen the slip nut that joins the tailpiece to the bottom of the basket strainer and remove the tailpiece. If a dishwasher hose or disposal is attached on this side, disconnect it first — and switch off a disposal's power at the breaker.
- 7
Kitchen: remove the locknut or snap ring
Under the sink, the strainer is held by either a large threaded locknut or a snap ring with screws. For a locknut, turn it counterclockwise with a spud wrench or by tapping a lug with a screwdriver and hammer. For a snap-ring style, loosen the screws, then pry the ring out of its groove with a flathead screwdriver.
- 8
Kitchen: lift out the basket strainer
Push the strainer body up from below and lift it out of the sink. Hold the strainer from above with pliers handles in the crossbars if it spins while you loosen the locknut.
- 9
Clean the sink opening
Scrape off old putty and gasket residue with a plastic putty knife, then clean with a mild cleaner and dry completely. Check the drain opening for cracks or chips — a damaged opening won't seal.
- 10
Reinstall the drain
Press a rope of plumber's putty under the new flange and set it in the opening. From below, add the rubber gasket, friction washer and locknut in the order shown in the instructions, and tighten while keeping the flange centered. Wipe off squeezed-out putty, then reconnect the tailpiece, P-trap and (for bathrooms) the pivot rod and clevis.
- 11
Test for leaks
Remove the rag from the wall pipe before reconnecting the trap. Fill the sink, then open the drain and watch every joint with a flashlight and dry paper towel. Tighten slip nuts a quarter turn at a time if you see drips.
Common mistakes
- Forgetting to remove the rag from the wall pipe before reconnecting the P-trap.
- Using plumber's putty on marble, granite or some composite sinks without checking — certain putties can stain stone.
- Overtightening plastic slip nuts and cracking them; hand-tight plus a small turn is usually enough.
- Putting the rubber gasket above the sink instead of below it, or the friction washer between gasket and sink.
- Buying a new pop-up drain without checking whether your sink has an overflow hole — drains are sold with and without overflow openings.
Frequently asked questions
Can I remove a sink drain without a special tool?
Usually, yes. Spread the jaws of needle-nose pliers inside the drain's crossbars, slide a screwdriver between the handles, and use it as a lever while someone loosens the locknut below. A drain key is cheaper than a ruined flange, though, and makes the job much easier.
Should I use plumber's putty or silicone on a sink drain?
Plumber's putty is the traditional choice for drain flanges and stays pliable, which makes future removal easy. Silicone is often recommended for stone sinks or plastic drains. Check the instructions for your sink and drain.
How do I loosen a corroded sink drain locknut?
Spray it with penetrating oil and wait 15 minutes. Then use channel-lock pliers or a spud wrench. As a last resort on a metal drain you are replacing anyway, carefully cut the tailpiece with a hacksaw below the nut.
What's the difference between a pop-up drain and a basket strainer?
A pop-up drain is the bathroom style with a stopper raised by a lift rod behind the faucet. A basket strainer is the kitchen style with a removable basket that catches food. They are sized differently and aren't interchangeable. Kitchen sinks with a garbage disposal use the disposal's flange instead of a strainer.
Why does my sink drain still leak after reinstalling?
Leaks under the flange usually mean the putty or gasket wasn't seated evenly. Leaks at slip joints mean a washer is missing, crooked or old. A leak at the pivot nut on a bathroom drain often means its small gasket needs replacing.
Related guides
- GuideHow to Remove a Shower Drain CoverIdentify your shower or tub drain cover — screw-in, snap-in, screwed grate, twist-and-lift or toe-touch — then remove it, clear the hair clog and put it back.
- GuideHow to Replace a Garbage DisposalSwap out a dead or leaking garbage disposal in an afternoon: cut the power, remove the old unit, wire the new one, seat the mounting ring and leak-test everything.
- GuideHow to Install a BathtubAn honest walkthrough of installing an alcove bathtub: removing the old tub, checking the subfloor, setting a ledger and mortar bed, connecting the drain and overflow, and waterproofing.