Home Repair
How to Fix a Leaky Faucet
Identify whether you have a compression, cartridge, ball or ceramic-disc faucet, then shut off the water and replace the worn washer, O-ring or cartridge to stop the drip.
A dripping faucet is more than annoying — it wastes water around the clock and leaves mineral stains in the sink. The fix is usually one small worn-out part: a rubber washer, an O-ring, or a cartridge. The tricky bit is knowing which one your faucet uses, because there are four basic designs and they come apart differently.
Spend a minute identifying your faucet before you buy anything. Then the repair is mostly unscrewing parts in order and putting new ones back.
Identify your faucet type
| Type | How to recognize it | What usually wears out |
|---|---|---|
| Compression | Two handles (hot and cold) that you twist and tighten down to shut off; you feel them squeeze to a stop | Rubber seat washers and stem O-rings |
| Cartridge | One or two handles that move smoothly with no squeeze at the end; single-handle models often lift up and down | The cartridge or its O-rings |
| Ball | One handle on a rounded, dome-shaped cap that pivots in all directions | Rubber seats, springs and O-rings, sometimes the ball |
| Ceramic disc | One lever over a wide, cylinder-shaped body; very smooth, firm motion | Rubber seals on the disc cartridge, or the cartridge itself |
Most modern single-handle faucets are cartridge or ceramic-disc designs. Many older two-handle faucets are compression. If you're unsure, take the handle off — what you see inside will make it clear.
Finding the right parts
Look for a brand logo on the faucet, the handle or the escutcheon plate, and check under the sink for a tag or the original paperwork. Many brands sell parts and sometimes send warranty replacements directly. Hardware stores carry common cartridges and faucet repair kits, but the safest approach is to bring the old part and match it side by side.
If the faucet drips because the whole thing is worn out, or the sink drain also leaks, it may be time for a bigger project — see how to remove a sink drain.
Step by step
- 1
Identify your faucet type
Use the table below. Count the handles, notice how they move, and look for a brand name on the faucet or under the sink. Knowing the type and brand tells you which part to buy.
- 2
Shut off the water
Close both shutoff valves under the sink by turning them clockwise. Open the faucet to let pressure and leftover water drain out. If there are no under-sink valves, shut off the main water supply.
- 3
Cover the drain and lay out a towel
Close the drain stopper or stuff a rag in it so small screws and clips can't fall in. Lay a towel in the sink and line parts up on it in the order you remove them — a quick phone photo at each step helps.
- 4
Remove the handle
Pry off the decorative cap with a thin blade to reach the handle screw, or look for a small set screw on the side or underneath the handle that takes a hex key. Remove the screw and pull the handle straight off.
- 5
Take out the stem or cartridge
On a compression faucet, unscrew the packing nut and turn the stem out. On cartridge and ceramic-disc faucets, remove the retaining nut or clip, then pull the cartridge straight up — a cartridge puller helps if it's stuck. On a ball faucet, unscrew the cap and lift out the cam, ball, seats and springs.
- 6
Take the old part to the store
Faucet parts vary by brand and model and many look alike. Bring the old cartridge, stem or washer with you so you can match it exactly, or order by the model number from the manufacturer.
- 7
Replace the worn parts
Compression: replace the rubber seat washer and its brass screw, plus the O-ring on the stem. Cartridge and ceramic-disc: install the new cartridge, lined up the same way the old one was. Ball: replace the seats, springs and O-rings, and the ball if it's scratched. Coat new O-rings with silicone grease.
- 8
Clean the valve seat and housing
Wipe out the faucet body and scrub mineral scale with a toothbrush dipped in vinegar. On compression faucets, check the brass seat at the bottom of the body; if it's pitted, replace it with a seat wrench or have it reground.
- 9
Reassemble and turn the water back on
Put everything back in reverse order, snug but not overtightened. Open the shutoff valves slowly with the faucet partly open to bleed out air, then run hot and cold. Check that the drip has stopped and no water leaks from the handle base.
Common mistakes
- Forgetting to plug the drain and losing a tiny screw or clip down it.
- Buying a replacement cartridge by guessing instead of bringing the old one or the model number.
- Installing a cartridge rotated the wrong way, which swaps hot and cold.
- Cranking the packing nut so tight the handle becomes stiff or the brass cracks.
- Turning the water back on with the faucet closed, which can blast debris into a new cartridge.
Frequently asked questions
Why does my faucet drip from the spout?
A drip from the spout means the part that shuts off the water isn't sealing — a worn washer or seat in a compression faucet, a worn cartridge, worn ball-faucet seats and springs, or worn ceramic-disc seals.
Why does water leak around the handle?
Leaks at the base of the handle usually come from a worn O-ring or a loose packing nut. Replacing the O-ring and adding a little silicone grease often fixes it.
Can I fix a faucet without shutting off the water?
No. Opening the faucet body under pressure will spray water and can flood the cabinet. Always close the shutoff valves or the main supply first.
Should I repair or replace an old faucet?
Repair it if parts are available and the body is in good shape. Replace it if the faucet is badly corroded, parts are discontinued, the base leaks, or you've already repaired it several times.
Do faucets come with a lifetime warranty?
Many major brands offer limited lifetime warranties on cartridges and seals for the original buyer. Check the manufacturer's website before buying parts — they may send replacements for free.
Related guides
- GuideHow to Remove a Sink Drain (Bathroom and Kitchen)Remove a bathroom pop-up drain or a kitchen basket strainer step by step: stopper, pivot rod, P-trap, locknut and flange — plus how to reinstall it without leaks.
- GuideHow to Fix a Running ToiletFind out why your toilet keeps running — flapper, chain, float, fill valve or overflow tube — with a simple food-coloring test, then replace the flapper or fill valve yourself.
- GuideHow to Unclog a DrainClear a slow or stopped sink or tub drain with hot water, a plunger, a drain snake or by cleaning the P-trap — plus what not to pour down it and how to tell when the problem is the main line.