Skip to content

Home Repair

How to Replace a Garbage Disposal

Swap out a dead or leaking garbage disposal in an afternoon: cut the power, remove the old unit, wire the new one, seat the mounting ring and leak-test everything.

When a garbage disposal hums but won't spin, leaks from its housing, or just grinds like a cement mixer, replacing it is often cheaper than repairing it. The job combines a little plumbing and a little electrical work, but nothing exotic: a mounting ring that twists on and off, two drain connections, and three wires.

Plan on a couple of hours the first time. Most of that is lying on your back in the sink cabinet, so put down a towel and grab a headlamp.

Corded or hardwired: which do you have?

Look under the sink before you buy anything. How your current disposal gets power decides how much electrical work is involved.

What you seeWhat it meansWhat to do
A cord from the disposal plugged into an outlet under the sinkCorded installationBuy a disposal that includes a cord, or a cord kit rated for disposals
A cable entering the bottom of the disposal through a clamp, no plugHardwired installationTurn off the breaker, then connect black, white and ground to the new unit
No outlet and no cable — you're adding a disposal for the first timeNew circuit or switch neededHire a licensed electrician; local codes govern disposal circuits

Choosing the replacement

The easiest swap is the same brand and mounting system as your old unit, but any standard disposal fits a standard 3 1/2-inch sink drain. Check the height of the new unit's discharge outlet against your old one — if it sits lower, the trap arm may need adjusting so water still drains downhill. Our garbage disposal roundup compares horsepower, noise insulation and warranty length.

Always follow the installation instructions that come with your new disposal; the steps below describe the most common twist-lock mounting system.

Troubleshooting after installation

ProblemLikely causeFix
Hums but doesn't spinJammed impellersPower off, insert the hex key into the socket on the bottom and work it back and forth
Doesn't run at allTripped reset button or breakerPress the red reset button on the bottom; check the breaker
Dishwasher won't drainKnockout plug still in placeRemove the disposal's hose and knock out the plug
Water drains slowlyTrap arm runs uphill from the outletLower or replace the trap arm so it slopes toward the wall

Related jobs

Before you buy a new unit, try resetting the garbage disposal — a jam or a tripped overload is the most common reason a disposal hums or goes silent. Putting in a new dishwasher at the same time? See how to install a dishwasher for the drain loop and supply line, and if the disposal's wall switch is worn out, here's how to replace a light switch.

Step by step

  1. 1

    Shut off power at the breaker

    Unplug the disposal if it's corded, then switch off its circuit at the breaker panel either way. Flip the wall switch to confirm nothing happens, and check the wires or outlet with a non-contact voltage tester before you touch them.

  2. 2

    Clear the cabinet and disconnect the drain lines

    Empty the sink base and set a bucket under the disposal. Loosen the slip nut where the discharge tube meets the P-trap, and loosen the clamp on the dishwasher drain hose (if you have one) and pull it off the disposal's inlet. Expect some dirty water.

  3. 3

    Remove the old disposal

    Support the unit from below with one hand — it is heavier than it looks. Insert a screwdriver or the disposal wrench into one of the lugs on the lower mounting ring and turn it counterclockwise (as seen from below). The disposal will drop free once the ring unlocks.

  4. 4

    Disconnect the old unit's wiring

    Flip the old disposal over and remove the electrical cover plate on the bottom. Unscrew the wire nuts, separate the wires, and loosen the cable clamp. If it was corded, simply keep the cord with the old unit unless you plan to reuse it on a compatible new one.

  5. 5

    Remove the old mounting assembly and clean the sink flange

    Loosen the three mounting screws on the upper ring, pry off the snap ring with a flathead screwdriver, and push the sink flange up out of the drain hole. Scrape old putty off the sink with a plastic scraper and wipe it clean and dry.

  6. 6

    Install the new sink flange with plumber's putty

    Roll a rope of plumber's putty about as thick as a pencil and press it around the underside of the new flange. Push the flange down into the drain opening and set something heavy in the sink to hold it. From below, slide on the fiber gasket, backup ring and mounting ring, snap the retaining ring into its groove, then tighten the mounting screws evenly until the flange is snug. Wipe away squeezed-out putty.

  7. 7

    Knock out the dishwasher plug (if you have a dishwasher)

    New disposals ship with the dishwasher inlet sealed by a plastic plug. If a dishwasher drains into the disposal, set the disposal on its side, put a long screwdriver or punch against the plug from inside the inlet, and tap it with a hammer until it pops inward. Fish the loose plug out of the grinding chamber before you mount the unit. Skip this step if you have no dishwasher.

  8. 8

    Wire the new disposal

    For a corded setup, attach the power cord kit to the disposal following the manufacturer's diagram. For a hardwired setup, run the cable through a strain relief connector, join black to black and white to white with wire nuts, and fasten the bare or green wire under the green ground screw. Tuck the wires in and replace the cover plate.

  9. 9

    Hang and lock the disposal

    Lift the disposal so its top lines up with the mounting ring, then turn the lower ring clockwise until all three lugs ride up the ramps and lock. Rotate the unit so the discharge outlet points toward the drain before the final turn.

  10. 10

    Reconnect the discharge tube and dishwasher hose

    Attach the discharge tube to the disposal outlet with its gasket and flange, then connect it to the P-trap with the slip nut. You may need to trim the tube or swap the trap arm if the heights don't match. Push the dishwasher hose onto the inlet and tighten its clamp.

  11. 11

    Restore power and leak-test

    Plug in or turn the breaker back on. Run cold water and switch the disposal on for a few seconds. Then fill the sink with a few inches of water, pull the stopper and watch every joint with a flashlight and a dry paper towel. If a dishwasher is connected, run a short cycle and check the hose connection too.

Common mistakes

  • Working on the wiring with the breaker still on because the wall switch is off — the switch may not break every conductor.
  • Forgetting to knock out the dishwasher plug, which makes the dishwasher back up and leave standing water.
  • Leaving the knocked-out plug inside the grinding chamber, where it rattles or jams the impellers.
  • Overtightening the mounting screws on one side, which tilts the flange and causes a slow leak at the sink.
  • Using plumber's putty on a stone or composite sink without checking — some putties stain; follow the sink maker's advice or use the gasket provided.

Frequently asked questions

Can I replace a garbage disposal myself?

Yes, if the new unit plugs into an existing outlet under the sink or you're comfortable connecting three wires to an existing circuit. If there's no power under the sink, or you'd need a new circuit or switch, hire a licensed electrician for that part.

Can I reuse the old mounting ring?

Sometimes. Many models from the same manufacturer share a mounting system, but different brands usually don't. It's simplest and most leak-proof to install the mounting assembly that comes with the new disposal.

Do I need plumber's putty or silicone for the sink flange?

Most manufacturers call for plumber's putty under the sink flange. Some newer units include a rubber gasket instead. Use whatever the instructions for your model specify.

What size garbage disposal do I need?

For most households a 1/3 to 1/2 horsepower unit is enough; larger households or heavy cooks often prefer 3/4 HP. See our garbage disposal roundup for how size, noise and grind stages compare.

Why is my new disposal leaking?

Locate the drip first. Leaks at the top are usually the sink flange (re-seat it with fresh putty). Leaks at the side come from the discharge tube gasket or the dishwasher hose clamp. Leaks from the bottom of the housing usually mean an internal seal failure — that unit needs replacing under warranty.