Skip to content

Home Repair

How to Install a Bathtub

An honest walkthrough of installing an alcove bathtub: removing the old tub, checking the subfloor, setting a ledger and mortar bed, connecting the drain and overflow, and waterproofing.

Installing a bathtub is a real project, not an afternoon job. It combines demolition, framing, plumbing, waterproofing and finish work, and the tub must be level, fully supported and leak-free before the walls close up. Done well, it lasts decades. Done hastily, it can leak into the subfloor for months before anyone notices.

This guide covers the most common situation: replacing a standard 60-inch alcove tub (three walls around it) with a new one where the drain and faucet stay roughly in the same place. Freestanding and drop-in tubs follow different steps. Use it to understand the whole job, decide which parts you'll do yourself, and talk confidently with a plumber about the rest.

Is this a DIY job for you?

Part of the jobDIY-friendly?Notes
Removing tile and wallboardYesMessy and physical, but straightforward
Removing a steel or acrylic tubUsuallyNeeds two people
Removing a cast iron tubWith careVery heavy; many people break it up in place
Subfloor and framing repairModerateRot or joist damage may need a contractor
Ledger board, mortar bed, levelingYes, with patienceFollow the tub maker's instructions exactly
Drain and overflow connectionModerateHard to reach; leaks hide behind walls
Moving drain or supply lines, replacing the valvePro recommendedOften requires a permit and soldering or crimping
Waterproofing and tileYes, with researchThe waterproof layer must be continuous

Choosing the new tub

Measure the alcove's length, width and the height of the existing valve, and note which side the drain is on. Acrylic tubs are light and warm to the touch; enameled steel is affordable but can sound hollow without support; cast iron is durable but very heavy. Our alcove bathtub roundup compares materials and sizes, and a matching drain and overflow kit saves a trip to the store.

Read the tub's installation instructions before you buy supplies — they specify whether a ledger or mortar bed is required, how to fasten the flange, and what clearances the warranty depends on. Follow them, and your local building codes, over any general guide, including this one.

Related jobs

Pulling the toilet to get the tub in? See how to replace a toilet for resetting it on a fresh seal. For the final seal around the new tub, follow our guide to caulking a bathtub.

Step by step

  1. 1

    Shut off the water and remove the old fixtures

    Turn off the water to the bathroom (or the whole house) and open the tub faucet to drain the lines. Remove the spout, handle trim and showerhead, then unscrew the overflow cover and the drain flange so the old tub is disconnected from the drain.

  2. 2

    Open the walls and remove the old tub

    Cut away tile and wallboard to about 6–12 inches above the tub rim so you can reach the flange. Remove the nails or screws holding the flange to the studs. Steel and acrylic tubs can often be pried out; cast iron is very heavy, so many people break it up with a sledgehammer under a heavy tarp while wearing full eye and ear protection. Get help either way.

  3. 3

    Inspect the subfloor and framing

    With the tub out, check the subfloor for soft spots, rot or water stains, and replace damaged sections before going further. Check that the alcove is square and the right size for the new tub, and that the floor is reasonably flat. A tub full of water and a person is a heavy load — the floor must be solid.

  4. 4

    Check the drain location and do a dry fit

    Compare the drain opening in the floor with the drain position on the new tub. Slide the tub in temporarily (or measure carefully) to confirm the drain lines up, the tub sits level, and the supply valve will end up where you want it. Adjusting the drain or supply lines is the point where many DIYers bring in a plumber.

  5. 5

    Install the ledger board

    Mark the height of the underside of the tub's flange on the back wall studs, then screw a level 2x4 ledger to the studs along that line (and on the end walls if the manufacturer calls for it). The ledger supports the tub's edge so the flange doesn't carry the weight.

  6. 6

    Pre-assemble the drain and overflow

    Most installers attach the drain and overflow kit to the tub before it goes in, following the kit instructions. Seal the drain flange with putty or silicone as specified, and seat the overflow gasket squarely so it doesn't leak behind the wall where you can't see it.

  7. 7

    Set the mortar bed, if the manufacturer requires it

    Many acrylic, fiberglass and steel tubs require a bed of mortar or another setting compound under the base to support it and stop flexing. If yours does, mix it to the consistency described in the instructions and spread mounds on the subfloor where the tub's base will sit, keeping it clear of the drain opening. Some tubs have integral supports and need no mortar; follow your tub's installation guide.

  8. 8

    Set and level the tub

    With a helper, lower the tub into place so its rim sits on the ledger and its base settles into the mortar. Connect the drain shoe to the waste pipe while you can still reach it. Check level along the rim in both directions and press or shim until it's level before the mortar sets.

  9. 9

    Fasten the tub flange

    Secure the flange to each stud as the manufacturer directs — usually with corrosion-resistant screws or galvanized roofing nails placed just above the flange, with the head lapping over it, or through pre-drilled holes. Don't drive fasteners through acrylic or fiberglass flanges unless the instructions say to, as they can crack.

  10. 10

    Connect the plumbing and test for leaks

    Finish the drain and overflow connections and reinstall or connect the valve. Fill the tub to just above the overflow and let it drain, watching every joint from the access panel or below. Fix any drips now — once walls go back up, leaks are hidden.

  11. 11

    Install backer board and waterproofing

    Hang cement board or another tile backer so it overlaps the tub flange, stopping a small gap above the tub rim. Apply a waterproofing membrane or liquid waterproofing as the product directs. This layer, not the tile or grout, is what keeps water out of the wall.

  12. 12

    Finish, seal and let it cure

    Tile or install the surround, reinstall the trim, and run a bead of 100% silicone where the tub meets the walls. Many pros fill the tub with water before caulking so the joint is at its widest. Let mortar and sealant cure fully, per their labels, before using the tub.

Common mistakes

  • Skipping the ledger board or mortar bed the manufacturer calls for, which leaves the tub flexing, cracking or creaking.
  • Buying a tub with the drain on the wrong side for your plumbing (tubs are sold as left-hand or right-hand drain).
  • Closing up the walls before leak-testing the drain and overflow connections.
  • Relying on tile and grout as the waterproof layer instead of a proper membrane over the backer board.
  • Not checking that the new tub fits through the bathroom door and hallway before buying it.
  • Doing plumbing or structural changes without the permits and inspections your area requires.

Frequently asked questions

Can I install a bathtub myself?

An experienced DIYer can install a like-for-like alcove tub where the drain and valve stay in the same place. Moving supply or drain lines, working with cast iron, or changing the floor structure is usually a job for a licensed plumber or contractor. Many homeowners do the demolition and finishing themselves and hire out the plumbing.

Do I need a permit to replace a bathtub?

It depends on where you live. Many jurisdictions require a plumbing permit when drain or supply lines are changed, and some require one for any tub replacement. Check with your local building department before you start.

Do all bathtubs need a mortar bed?

No. Many acrylic, fiberglass and steel tubs call for one, while others have built-in leveling feet or foam bases. Cast iron tubs are often set directly on a level subfloor. The tub's installation instructions are the deciding factor — and using the wrong method can void the warranty.

How do I know which drain side I need?

Stand facing the tub's open side from outside the tub. If the drain is at your left, you need a left-hand drain tub; if it's at your right, a right-hand drain. Check the position of your existing drain before ordering.

How long before I can use a new bathtub?

Wait until the mortar bed, adhesives and silicone have cured — commonly at least 24 hours, and sometimes longer for tile setting materials and grout. Follow the cure times printed on each product.