Skip to content

Home Repair

How to Remove a Shower Drain Cover

Identify your shower or tub drain cover — screw-in, snap-in, screwed grate, twist-and-lift or toe-touch — then remove it, clear the hair clog and put it back.

A slow shower drain is almost always a hair clog sitting just a few inches below the cover. Getting to it is easy once you know what kind of cover you have — and that's the hard part, because shower and tub drains look similar but come off in completely different ways.

Start by identifying your cover with the table below, then follow only the steps that apply.

Which drain cover do I have?

What you seeTypeTools neededHow it comes off
Flat grate with one or two visible screwsScrew-held gratePhillips or flathead screwdriverRemove the screws, lift the grate
Flat grate, no screws, threads visible when you look closelyScrew-in grateNeedle-nose pliers or fingersTurn counterclockwise
Flat grate, no screws, sits flush in a ringSnap-in / pop-out grateFlathead screwdriver or putty knifePry up gently around the edge
Tub stopper you push with your foot to open and closeToe-touch (push-pull)Fingers, rubber grip, sometimes a screwdriverUnscrew the cap, then the body
Tub stopper with a small knob on topLift-and-turnSmall screwdriver or hex keyLoosen the set screw or unscrew the stopper
Small round knob over a hidden linkage, lever on the overflow plateTrip-lever tub drainScrewdriverRemove the overflow plate screws and pull the linkage up

If none of these match, look up your faucet or drain brand's instructions — some newer designs use proprietary clips.

Keeping it clear

Once the drain is flowing again, a simple drain hair catcher on top of the cover catches hair before it gets inside. For clogs that are deeper than your fingers can reach, a plastic hair-clog tool or a small hand-cranked drain snake is far safer for pipes than harsh chemicals.

Related jobs

With the cover off and the drain clear, finish the job: clean the grout, check the caulk line and re-caulk the tub if it's cracked or moldy, and consider an easy upgrade — replacing the shower head.

Step by step

  1. 1

    Identify the type of cover

    Look closely at the cover with a flashlight. Visible screws mean a screw-held grate. A smooth cap you can press is a toe-touch stopper. A knob on top means lift-and-turn. A flat grate with no screws is either snap-in or screw-in. Use the table above to match yours.

  2. 2

    Protect the drain opening

    Lay a small towel or a piece of tape over the floor of the shower near the drain so screws and small parts can't roll in. Put on gloves — what comes out of a shower drain is unpleasant.

  3. 3

    Screw-held grate: remove the screws

    Unscrew the one or two screws in the grate with a screwdriver that fits the slot snugly, then lift the grate off. If a screw is stuck, apply penetrating oil, wait a few minutes, and press firmly while you turn.

  4. 4

    Snap-in or screw-in grate: pry or twist

    Try twisting the grate counterclockwise first — many unscrew by hand or with needle-nose pliers set in two of the slots. If it doesn't turn, it's probably a snap-in cover: work a flathead screwdriver under the edge at a few points and gently pry it up. Protect the tile or pan with a folded rag under the screwdriver.

  5. 5

    Toe-touch stopper: unscrew the cap

    Push the stopper to the open position. Hold the body and turn the cap counterclockwise to unscrew it. Some designs then reveal a center screw or a threaded post — remove that too and lift the body out. Wrap the cap in duct tape or use a rubber jar opener if it's too slippery to grip.

  6. 6

    Lift-and-turn stopper: loosen the set screw or unscrew

    Open the stopper and look under the knob or on the side of the stopper body for a small set screw. Loosen it with a screwdriver or hex key, then lift the stopper off its post. If there's no set screw, turn the entire stopper counterclockwise to unscrew it.

  7. 7

    Pull out the hair clog

    Shine a flashlight into the drain. Use needle-nose pliers or a barbed plastic hair-clog tool to hook and pull out the mat of hair and soap scum. Feed a small drain snake a little further if water still drains slowly, then flush with hot (not boiling) water.

  8. 8

    Clean the cover and threads

    Scrub the cover, stopper and drain threads with an old toothbrush and a little dish soap. Look at O-rings and gaskets — replace any that are cracked or flattened.

  9. 9

    Reinstall the cover

    Wipe a light coat of plumber's grease on threads and O-rings. Screw or press the cover back into place, or reinstall the stopper and tighten its set screw. Don't overtighten grate screws; snug is enough and keeps them from stripping next time.

  10. 10

    Test the drain

    Run the shower for a minute and watch the water level. It should drain without pooling. For a tub stopper, close and open it a few times to make sure it seals and releases.

Common mistakes

  • Pouring boiling water into a drain with PVC pipes — very hot water can soften plastic fittings. Hot tap water is enough.
  • Prying a snap-in cover with a bare screwdriver against tile or acrylic, which chips the finish.
  • Using a worn or wrong-size screwdriver on corroded screws and stripping the heads.
  • Mixing chemical drain cleaners or using them before removing the cover, then splashing caustic water on your hands.
  • Letting the small cover screws fall into the drain.

Frequently asked questions

How do I remove a shower drain cover with no screws?

It is usually a snap-in or screw-in cover. First try turning it counterclockwise with needle-nose pliers in two slots. If it won't turn, gently pry around the edge with a flathead screwdriver wrapped in tape or a thin putty knife.

What do I do if a drain cover screw is stripped?

Press a wide rubber band between the screwdriver tip and the screw head for extra grip. If that fails, use a screw extractor bit in a drill on low speed. Replace stripped screws with stainless steel ones so they don't corrode again.

How often should I clean a shower drain?

Pulling hair out of the drain every month or two keeps most showers flowing freely. A drain hair catcher cuts down how often you need to remove the cover at all.

Do I need a special tool to remove a shower drain?

To remove the cover, no — a screwdriver and pliers are enough. To remove the threaded drain body itself, you'll need a drain key or shower drain wrench, and that's a bigger job that may disturb the waterproof seal.

Why is my shower still draining slowly after cleaning the cover?

The clog is probably deeper than you can reach with pliers. Use a drain snake through the opening. If the drain is still slow or several fixtures back up at once, the blockage is in the main line and a plumber should take a look.