Home Repair
How to Unclog a Toilet
Stop the overflow, then clear a clogged toilet with a flange plunger, dish soap and hot water, or a closet auger — and what never to pour or push into the bowl.
A clogged toilet feels like an emergency, but the first move is simple: stop the water. Once the bowl can't overflow, you have time to clear it properly — and almost every toilet clog gives way to the right plunger used the right way.
The usual culprits are too much toilet paper at once, wipes, or something that should never have been flushed. Here's how to fix it without scratching the bowl or flooding the floor.
Where to shut off the water
The supply valve is on the wall or floor behind the toilet, connected to the bottom of the tank by a short hose. Turn the handle clockwise until it stops. Some newer valves are quarter-turn: turn the lever so it's crosswise to the pipe. If the valve is stuck, don't force it — use the flapper trick in step 1 and deal with the valve later.
What to use, and when
| Situation | Best tool | Why |
|---|---|---|
| Bowl full, water draining slowly | Flange plunger | Pressure and suction move most soft clogs |
| Plunging moves water but the clog comes back | Dish soap and hot water, then plunge | Softens and lubricates paper clogs |
| Plunging doesn't change anything | Closet auger | Reaches through the trap built into the toilet |
| A toy, phone or other solid object went down | Closet auger, or remove the toilet | Plunging can wedge it in tighter |
| Tub or sink backs up when you flush | Call a plumber | Main drain line blockage |
A good flange plunger is worth having before you need it, and a closet auger is the tool plumbers reach for next because its rubber guard protects the porcelain. A regular sink drain snake is the wrong tool here; its bare metal head can scratch the bowl.
For slow sinks and tubs, see how to unclog a drain. If the tank keeps running after the clog is gone, follow how to fix a running toilet.
Step by step
- 1
Stop the water before it overflows
If the bowl is rising, don't flush again. Turn the supply valve behind the toilet clockwise to shut it. If you can't reach it in time, lift the tank lid and push the flapper down over the drain hole to stop water entering the bowl, then lift the float to stop the fill valve.
- 2
Protect the floor
Lay towels around the base and put on gloves. If the bowl is nearly full, bail some water into a bucket so it doesn't slosh over when you plunge — but leave enough to cover the plunger cup.
- 3
Seat the flange plunger
Fold the flange out so it fits into the drain opening at the bottom of the bowl. Lower the plunger in at an angle so the cup fills with water instead of trapping air, then press it into the opening to make a seal.
- 4
Plunge with steady strokes
Push down gently on the first stroke to push out any air, then pump firmly up and down 15–20 times, keeping the seal. Pull up sharply on the last stroke. Repeat a few rounds. When the water drops with a gulp, the clog has moved.
- 5
Try dish soap and hot water
If plunging isn't working, squirt a generous amount of dish soap into the bowl, then pour in a bucket of hot tap water from waist height. Let it sit for 15–20 minutes. The soap lubricates the clog and the warm water softens it. Then plunge again.
- 6
Use a closet auger
Pull the auger handle up so the cable is retracted, set the curved end in the bottom of the bowl with the rubber guard against the porcelain, and crank the handle clockwise while pushing the cable down. When it stops, crank and work it back and forth to break up or snag the clog, then retract it and flush a test.
- 7
Test with a careful flush
Turn the supply valve back on and let the tank fill. Lift the lid and keep a hand near the flapper the first time you flush, so you can drop it if the water rises again.
- 8
Clean up
Rinse the plunger and auger in the bowl with a final flush, spray them with disinfectant and let them dry. Wash the towels in hot water and wipe the floor around the base.
Common mistakes
- Flushing again and again to see if it's cleared, which overflows the bowl.
- Pouring chemical drain cleaner into a toilet — it rarely reaches the clog, can damage the wax seal, and makes plunging or snaking hazardous.
- Pouring boiling water into the bowl, which can crack the porcelain.
- Using a flat cup plunger that can't seal in the toilet's drain opening.
- Pushing a metal sink snake or coat hanger into the bowl and scratching the porcelain.
- Treating wipes labeled flushable, paper towels or cotton swabs as safe to flush.
Frequently asked questions
What's the difference between a toilet plunger and a sink plunger?
A toilet (flange) plunger has a soft rubber sleeve that sticks out below the cup and fits into the curved drain opening. A sink (cup) plunger is flat and seals on flat surfaces. Using a cup plunger on a toilet is the most common reason plunging doesn't work.
How do I unclog a toilet without a plunger?
Try dish soap and a bucket of hot tap water, wait 15–20 minutes, and flush carefully. If that fails, a closet auger is the next step. Avoid chemical drain cleaners in toilets.
Why does my toilet keep clogging?
Frequent clogs can come from using a lot of paper per flush, flushing wipes, an object stuck in the trap, a low-flow toilet with weak flush performance, or a partial blockage farther down the drain line. If several drains back up at once, suspect the main line.
Can a toy or object stuck in the toilet be removed?
Sometimes a closet auger will hook it, but plunging can push it deeper. If you know something solid went down and the auger doesn't bring it back, the toilet may need to be pulled from the floor to reach it from below.
Is it safe to leave a clogged toilet overnight?
It's fine if the water level is stable and the supply valve is off. Sometimes a soft clog dissolves on its own overnight. Don't flush it until you've confirmed the water has drained down.
Related guides
- GuideHow to Unclog a DrainClear a slow or stopped sink or tub drain with hot water, a plunger, a drain snake or by cleaning the P-trap — plus what not to pour down it and how to tell when the problem is the main line.
- GuideHow to Fix a Running ToiletFind out why your toilet keeps running — flapper, chain, float, fill valve or overflow tube — with a simple food-coloring test, then replace the flapper or fill valve yourself.
- GuideHow to Replace a ToiletPull out an old toilet and set a new one without leaks: measure the rough-in, inspect the flange, choose a wax or wax-free seal, and tighten everything just enough.