Home Repair
How to Replace a Shower Head
Swap a shower head in about 20 minutes: unscrew the old one, clean the threads, wrap thread seal tape the right way, tighten without crushing anything, and pick a legal flow rate.
Replacing a shower head is one of the few plumbing jobs that needs no water shutoff and almost no tools. The head simply screws onto the end of the shower arm, and the whole swap takes about as long as a shower.
It's also one of the quickest ways to change how a bathroom feels: better spray, a handheld wand for rinsing the tub, or a head that saves water without feeling weak.
Fixed vs. handheld
| Type | Good for | Things to know |
|---|---|---|
| Fixed shower head | Simple setups, rain-style sprays, the cleanest look | Spray direction adjusts only by tilting the ball joint |
| Handheld on a bracket | Rinsing kids, pets and the tub; seated showers | Hose connects at the arm; check hose length for your space |
| Combination (fixed + handheld) | Households that want both | Uses a diverter to switch or share water between heads |
| Handheld on a slide bar | Adjustable height for different users | Bar mounts to the wall, so you'll drill into tile or use an existing bracket |
Every standard shower head fits a 1/2-inch threaded shower arm, so you don't need to match the old brand. Our shower head roundup compares spray patterns and flow rates, and our handheld shower head roundup covers hose length and mounting options.
A note on flow rates
Since the 1990s, US federal rules have limited new shower heads to 2.5 gallons per minute. Some states set stricter limits, commonly 1.8 or 2.0 gallons per minute, and the EPA's WaterSense label marks heads that use 2.0 gallons per minute or less. Most heads hit these numbers with a small flow restrictor inside the connector.
Lower flow doesn't have to mean a weak shower; spray design matters as much as gallons per minute. A lower-flow head also means less hot water used per shower, which can help if your water heater runs out quickly. If yours does, our guide to fixing a water heater covers the common causes.
Getting the tape right
Thread seal tape works by filling the tiny gaps in the threads. Wrap it the wrong way and tightening the head pushes it off the threads into a wad. The rule: face the open end of the shower arm and wrap clockwise. Keep it snug and flat, two or three layers, and start just behind the first thread so loose strands don't end up clogging the new head.
Keeping the new head clear
Mineral deposits clog spray nozzles over time. Many heads have rubber nozzles you can rub with a fingertip to break buildup loose. For harder deposits, fill a plastic bag with white vinegar, tie it around the head for an hour, then run hot water through it. Check the manufacturer's care instructions first, especially for plated or specialty finishes.
Step by step
- 1
Protect the drain and the finish
Close the tub or shower drain, or lay a towel over it, so small washers can't disappear. Wrap a rag around the shower head's connecting nut so the wrench won't scratch it — or the shower arm, if you're keeping it.
- 2
Unscrew the old shower head
Turn the old head counterclockwise (as you face it). Many come off by hand. If yours is stuck, grip the nut with a wrench over the rag, and hold the shower arm steady with your other hand so it doesn't twist inside the wall.
- 3
Clean the shower arm threads
Peel off old thread tape and scrub the threads with an old toothbrush. If they're crusted with white or green deposits, wrap them in a vinegar-soaked rag for 30 minutes, then scrub again. Clean threads seal far better.
- 4
Check the shower arm
Look for cracks, deep corrosion or stripped threads. Give the arm a gentle wiggle; if it's loose in the wall, the fitting behind the wall may need attention. A corroded arm unscrews counterclockwise from the wall fitting and is cheap to replace.
- 5
Wrap thread seal tape clockwise
Starting at the end of the arm, wrap PTFE tape clockwise as you look at the end of the pipe — the same direction the new head will turn on. Pull it snug and make 2 to 3 wraps, keeping it off the very first thread so shreds don't end up in the head.
- 6
Check the new head's washer
Most shower heads have a rubber washer inside the connector. Make sure it's seated flat, and remove any packaging plugs. Leave the built-in flow restrictor in place.
- 7
Thread on the new head hand-tight, plus a little
Screw the new head onto the arm by hand, keeping it straight so it doesn't cross-thread. Tighten it hand-tight, then give it about a quarter turn more with the wrench over a rag if needed. Plastic connectors usually need hand-tightening only — follow the maker's instructions.
- 8
Mount the holder (handheld models)
For a handheld head, thread the bracket or diverter onto the arm first, then connect the hose to it and to the handset. Washers go inside each hose nut; hand-tighten these connections.
- 9
Run the water and check for leaks
Turn the shower on full and watch the connection. A small drip usually stops with another small turn. If it keeps leaking, remove the head, rewrap the tape and try again rather than forcing it tighter.
Common mistakes
- Wrapping thread seal tape counterclockwise, so it bunches and unwinds as you tighten the head.
- Twisting the shower arm while removing the old head, which can loosen the fitting inside the wall.
- Cranking a plastic or metal connector too hard and cracking it or crushing the washer.
- Leaving the old tape and mineral crust on the threads.
- Removing the flow restrictor, which wastes water and may conflict with local water rules.
Frequently asked questions
Which way do you wrap thread seal tape on a shower arm?
Clockwise as you look at the end of the arm. That's the same direction the shower head turns as you tighten it, so the tape stays smooth instead of peeling back. Two or three wraps is plenty.
Do I need thread seal tape if the shower head has a washer?
The washer does most of the sealing, but a few wraps of tape help prevent drips through the threads and make the head easier to remove later. Some manufacturers say tape isn't needed; follow your instructions if they say otherwise.
What is the maximum flow rate for a shower head?
The federal maximum in the US is 2.5 gallons per minute. Several states — including California, Colorado, Washington and others — set lower limits, often 1.8 or 2.0 gallons per minute. Shower heads with the EPA's WaterSense label use 2.0 gallons per minute or less.
Handheld or fixed shower head: which should I get?
A fixed head is simple and stays put. A handheld head on a hose makes it easier to rinse kids and pets, clean the tub and sit while showering, which helps people with limited mobility. Combination units give you both with a diverter. All of them fit the standard 1/2-inch shower arm.
Why is my new shower head leaking at the connection?
The washer may be missing or folded, the threads may be dirty or cross-threaded, or the tape may have been wrapped the wrong way. Remove the head, check the washer, rewrap the tape clockwise, and tighten it again by hand plus a little.
Related guides
- GuideHow to Caulk a BathtubStrip out moldy old caulk and lay a clean, watertight bead around your tub: removal, drying, choosing silicone or siliconized acrylic, the water-weight trick and the tape method.
- GuideHow to Fix a Leaky FaucetIdentify whether you have a compression, cartridge, ball or ceramic-disc faucet, then shut off the water and replace the worn washer, O-ring or cartridge to stop the drip.
- GuideHow to Remove a Shower Drain CoverIdentify your shower or tub drain cover — screw-in, snap-in, screwed grate, twist-and-lift or toe-touch — then remove it, clear the hair clog and put it back.