Cleaning
How to Clean Grout (Mildest Method First)
Brighten dirty grout without damaging tile or stone — start with warm water and a brush, then baking soda, oxygen bleach or steam, and seal it afterward so it stays clean.
Grout is the porous filler between tiles, and that porosity is the whole problem. It soaks up spills, soap scum, mop water and body oils, so a light gray line slowly turns dark brown, and white grout in a shower picks up pink and black mildew spots. Scrubbing harder with harsher chemicals is the reflex, but it can scratch tile, fade colored grout and etch natural stone.
The better approach is to start with the mildest method and only step up when you need to. Most grout comes clean with water, a good brush and some patience. Sealing it afterward is what keeps it that way.
Cleaning methods, mildest to strongest
| Method | Good for | Safe on natural stone? |
|---|---|---|
| Warm water and a brush | Routine dirt and light grime | Yes |
| Dish soap or pH-neutral cleaner | Greasy kitchen floors | Yes, if labeled pH-neutral |
| Baking soda paste | Stubborn spots, light stains | Generally yes; rinse well |
| Oxygen bleach | Set-in stains, mildew, dingy grout | Check the label; spot test |
| Steam | Deep grime on sealed ceramic and porcelain | Ask your installer or stone supplier first |
| Acidic cleaners (vinegar, lemon) | Not recommended for grout | No — acid etches stone |
A good grout brush matters more than the cleaner. Its narrow, stiff nylon bristles reach into the joint instead of skating over the tile.
Ceramic, porcelain or natural stone?
Ceramic and porcelain are tough and handle most grout cleaners. Natural stone is the one to protect. Marble, travertine and limestone are calcium-based and react with acid — even a splash of vinegar can leave a dull, rough spot called an etch mark. Stone often looks less uniform than ceramic, with natural veining, and feels cooler and heavier. If you're not sure what you have, use only pH-neutral cleaners and skip steam until you know.
Why sealing matters
Unsealed cement grout is like a sponge. A penetrating grout sealer fills the pores so spills and mop water bead up long enough to wipe away. It doesn't make grout stain-proof, but it makes routine cleaning far easier. Seal only after the grout is clean and fully dry, and wipe any sealer off the tile faces before it dries.
Step by step
- 1
Figure out what you're cleaning
Check whether the tile is ceramic, porcelain or natural stone such as marble, travertine, limestone or slate, and whether the grout is cement-based or epoxy. Stone and its grout need gentler, pH-neutral products. If you're not sure, treat it as stone.
- 2
Sweep or vacuum first
Remove loose dirt and grit so you don't grind it into the grout lines while scrubbing. On walls and showers, rinse with warm water.
- 3
Scrub with warm water
Dip a grout brush in warm water and scrub the lines in short back-and-forth strokes. Add a drop of dish soap or a pH-neutral tile cleaner for greasy kitchen floors. Wipe up the dirty water as you go. For lightly dirty grout, this is often enough.
- 4
Try a baking soda paste on stubborn spots
Mix baking soda with a little water into a thick paste, press it into the grout lines, let it sit 5–10 minutes, then scrub and rinse. It's mildly abrasive and safe for most surfaces, including stone, when rinsed well.
- 5
Use oxygen bleach for stains and mildew
Dissolve oxygen bleach powder in warm water according to the package, apply it to the grout, and let it sit for the label's time — often 10–15 minutes — while keeping it wet. Scrub, then rinse thoroughly. Check the label for stone compatibility and spot test on colored grout first.
- 6
Steam-clean deep dirt (optional)
A steam cleaner with a small nylon brush tip lifts grime from sealed ceramic and porcelain tile without chemicals. Work slowly along the grout lines and wipe up the loosened dirt right away. Skip steam on loose tiles, cracked grout, or stone your installer says shouldn't be steamed.
- 7
Rinse and dry completely
Mop or wipe the area with clean water to remove all cleaner residue, which can attract dirt. Then let the grout dry fully — usually at least 24 hours, or as long as the sealer label says.
- 8
Test whether the grout needs sealing
Drip a few drops of water on a grout line. If it beads up, the existing seal is working. If it soaks in and darkens the grout within a few minutes, it's time to seal.
- 9
Seal the grout
Apply a penetrating grout sealer to clean, dry cement-based grout with the applicator or a small brush, following the label. Wipe any sealer off the tile surface before it dries, and let it cure for the labeled time before showering or mopping. Epoxy grout generally doesn't need sealing.
Common mistakes
- Using vinegar, lemon juice or other acidic cleaners on marble, travertine or limestone — acid etches stone and can wear down cement grout over time.
- Mixing chlorine bleach with vinegar, ammonia or other cleaners, which can release toxic fumes.
- Scrubbing with a wire brush, which scratches tile and digs out grout.
- Leaving cleaner residue on the floor instead of rinsing, so the grout gets dirty again quickly.
- Sealing grout before it's fully dry, trapping moisture and dirt underneath.
Frequently asked questions
What is the best homemade grout cleaner?
Start with warm water and a stiff brush, then a baking soda paste for stubborn spots. For stains and mildew, oxygen bleach mixed with water is effective and gentler on colored grout than chlorine bleach. Avoid vinegar on natural stone.
Can I use vinegar to clean grout?
It's best avoided. Vinegar is acidic and can etch natural stone, and repeated use can slowly erode cement-based grout and break down sealer. A pH-neutral cleaner or oxygen bleach is a safer choice.
How often should grout be sealed?
It depends on the sealer and how much traffic and water the area gets. Many products last from about one to several years. Do the water drop test every so often — if water soaks in and darkens the grout, reseal.
Can I use chlorine bleach on grout?
Diluted chlorine bleach can kill mildew on white grout, but it can fade colored grout, and it must never be mixed with vinegar, ammonia or other cleaners. Ventilate well and rinse thoroughly. Oxygen bleach is usually the easier option.
What if the grout is still dark after cleaning?
Some discoloration goes deep into old, unsealed grout and won't scrub out. A grout colorant or stain pen can even out the color, and cracked or crumbling grout should be removed and replaced. Mildew that keeps returning in a shower can point to a ventilation or leak problem.
Related guides
- GuideHow to Caulk a BathtubStrip out moldy old caulk and lay a clean, watertight bead around your tub: removal, drying, choosing silicone or siliconized acrylic, the water-weight trick and the tape method.
- GuideHow to Clean Hardwood Floors Without Damaging ThemIdentify your floor's finish, then clean it the right way — dry dusting, damp (not wet) mopping with a pH-neutral cleaner, and removing scuffs and spots — plus what flooring makers say to avoid.
- GuideHow to Remove a Shower Drain CoverIdentify your shower or tub drain cover — screw-in, snap-in, screwed grate, twist-and-lift or toe-touch — then remove it, clear the hair clog and put it back.