Skip to content

Home Repair

How to Caulk a Bathtub

Strip out moldy old caulk and lay a clean, watertight bead around your tub: removal, drying, choosing silicone or siliconized acrylic, the water-weight trick and the tape method.

Fresh caulk is the cheapest way to make a tired bathroom look cared for, and it does a real job: it keeps water from running down behind the tub where it can rot the subfloor and wall framing. When the old bead is cracked, peeling or black with mildew, it's time to replace it.

The whole job is about preparation. Laying the bead takes ten minutes. Removing the old caulk, killing the mildew and letting everything dry is what decides whether the new bead lasts years or weeks.

Choosing the right caulk

Only use caulk labeled for kitchens and baths, which includes a mildew-resistant additive. Beyond that, the choice comes down to two types:

100% siliconeSiliconized acrylic latex
Water resistanceExcellentGood
Flexibility over timeStays flexibleCan stiffen and crack sooner
Ease of smoothingHarder; stickyEasier
CleanupSolvent or wipes while wetWater while wet
PaintableNoYes
Best forTub-to-tile and tub-to-wall joints in daily usePainted trim, or anyone wanting an easier first attempt

If you're unsure, 100% silicone is the safer bet around a tub that gets used every day. Our bath caulk roundup compares both types.

Why fill the tub with water

Tubs flex. When the tub is full and someone is standing in it, it drops very slightly and the joint with the wall opens up. If you caulk an empty tub, that first bath stretches the bead and can tear it loose. Filling the tub before caulking puts the joint in its "loaded" position, so the caulk cures at the widest gap it will ever see. Leave the water in until the caulk has set.

The tape method for clean lines

Painter's tape is the difference between a bead that looks professional and one that smears onto the tile. Tape both sides of the joint, lay the bead, smooth it once, and pull the tape immediately. If you wait until the caulk skins over, the tape drags the edge with it. Do one wall at a time so the caulk is still wet when you pull.

Keeping it clean

Run the exhaust fan during showers and for 20 to 30 minutes afterward, and wipe standing water off the joint when you can. A quick weekly spray with a bathroom cleaner keeps mildew from getting a foothold. If you're cleaning the tile too, our guide to cleaning grout covers that part of the job.

Step by step

  1. 1

    Cut out the old caulk

    Slice along both edges of the old bead with a utility knife or caulk removal tool, then peel or scrape it out. On acrylic or fiberglass tubs use a plastic scraper so you don't scratch the finish.

  2. 2

    Remove the residue

    Scrape off leftover film. Old silicone leaves a slick residue that new caulk won't stick to, so soften stubborn bits with a silicone caulk remover and scrape again. Latex caulk residue usually comes off with warm water and a scrub brush.

  3. 3

    Kill the mildew

    Scrub black spots in the joint with a mildew cleaner or a diluted bleach solution, following the product label, and rinse well. Never mix bleach with ammonia or acidic cleaners. If mold is behind the old caulk, keep cleaning until the joint is bare.

  4. 4

    Let the joint dry completely

    Wipe the area dry, then leave the bathroom fan running or a window open and let the gap dry for several hours — overnight is better. Caulk sealed over moisture won't bond and traps mildew behind it.

  5. 5

    Wipe with rubbing alcohol

    Just before you caulk, wipe both surfaces with rubbing alcohol on a clean rag to remove soap film and body oils. Let it flash off for a few minutes.

  6. 6

    Fill the tub with water

    Fill the tub most of the way with water. The weight makes the tub settle slightly, opening the joint to its widest. Caulk applied now won't be stretched and torn the first time someone steps in.

  7. 7

    Tape both sides of the joint

    Run painter's tape along the tub and along the wall, leaving a gap of about 1/8 to 1/4 inch over the joint. Press the edges down firmly so caulk can't creep under.

  8. 8

    Apply the bead

    Cut the caulk tube nozzle at a 45-degree angle, slightly smaller than the gap. Hold the gun at the same angle and push a steady, continuous bead along the joint, working one wall at a time. Slow and even beats fast.

  9. 9

    Tool the bead and pull the tape

    Smooth the bead with a caulk tool or a fingertip in a glove dipped in a little soapy water (for silicone) or plain water (for acrylic). Then pull the tape off right away at a low angle, away from the bead, before the caulk skins over.

  10. 10

    Let it cure before using the tub

    Leave the water in the tub until the caulk has set, then drain it. Don't shower or bathe until the cure time on the label has passed. Many bath caulks need about 24 hours; fast-cure products may be ready sooner.

Common mistakes

  • Caulking over old caulk or silicone residue, which peels off within weeks.
  • Sealing a damp joint and trapping moisture and mold behind the new bead.
  • Skipping the water-weight step, so the bead stretches and cracks the first time the tub is used.
  • Pulling the tape after the caulk has skinned over, which drags the edge into a ragged line.
  • Using the tub before the caulk has fully cured according to its label.

Frequently asked questions

Should I use 100% silicone or siliconized acrylic caulk around a tub?

100% silicone stays flexible and waterproof the longest and resists mildew well, so it's the usual pick for tub joints. It's harder to smooth, needs solvent cleanup and can't be painted. Siliconized acrylic latex is easier to tool, cleans up with water and is paintable, but typically doesn't last as long in constant water. Look for a product labeled for kitchens and baths either way.

Can I put new caulk over old caulk?

It's not recommended. New caulk doesn't bond well to old caulk, and fresh silicone won't stick to old silicone at all. Removing the old bead completely is the step that makes the new one last.

How long does tub caulk take to dry?

It depends on the product, so follow the label. Many silicone and siliconized acrylic bath caulks are dry to the touch within an hour but need about 24 hours before they're exposed to water. Cool or humid rooms slow curing down.

Why does my tub caulk keep turning black?

Mildew is growing on or behind it. That usually means the old caulk wasn't fully removed, the joint was damp when sealed, or the bathroom stays humid. Re-caulk on a fully dry joint and run the exhaust fan during and after showers.

What if the gap is too wide to caulk?

Gaps wider than about 1/4 inch tend to crack. Press foam backer rod into the gap first so the caulk bead stays a normal size. A gap that keeps growing can mean the tub or wall is moving and is worth having checked.