Home Repair
How to Install a TV Wall Mount
Mount a TV securely on drywall, plaster or brick: match the VESA pattern, pick the right height, find studs, drive lag bolts, level the bracket and hide the cables safely.
Getting a TV off the stand and onto the wall frees up space and puts the screen at a better height — but only if the mount is anchored properly. The hardware will hold far more than your TV weighs when it's in wood studs or solid masonry. Most failed mounts come down to the wrong anchor in the wrong wall.
This guide covers fixed, tilting and full-motion mounts on the three walls most people have: drywall over wood studs, old plaster and lath, and brick or concrete.
What anchors does my wall need?
| Wall type | How to tell | What to use |
|---|---|---|
| Drywall over wood studs | Knocking sounds hollow between studs; a stud finder works well | Lag bolts into the center of at least two studs |
| Drywall over metal studs | Magnet sticks to screws; the stud finder shows narrow studs | Anchors specifically rated for metal studs — check the mount maker's guidance |
| Plaster and lath | Hard, heavy wall in an older home; drilling makes white or gray dust | Lag bolts into studs; drill slowly with a sharp bit to avoid cracking the plaster |
| Brick or concrete | Masonry surface, or painted block | Masonry sleeve or wedge anchors in solid brick or block, not the mortar |
The weight rating on the box assumes correct installation. With an articulating arm, a TV extended 20 inches from the wall puts much more leverage on the top bolts than the same TV on a fixed mount, so use every hole the wall plate offers.
Picking a mount
Match three things: the VESA pattern on the back of the TV, the weight, and the stud spacing on your wall. A TV wall mount with a wide wall plate gives you more flexibility to hit studs and center the screen. A good stud finder takes most of the guesswork out of the job.
Always follow the instructions packed with your mount — hardware sizes, pilot-hole sizes and weight limits differ between models.
Related jobs
Moving the TV to a new spot? Patch the old holes in the drywall before you paint. And once the job is done, vacuum up drilling dust and see how to clean hardwood floors without scratching the finish.
Step by step
- 1
Check the VESA pattern and weight
Measure the distance between the mounting holes on the back of the TV, horizontally and vertically, in millimeters (for example 400 x 400). That's the VESA pattern. Confirm the mount lists that pattern and a weight rating above your TV's weight, which you'll find in the manual or on the spec label.
- 2
Choose the height and location
Sit where you'll watch and have a helper hold a piece of cardboard the size of the screen against the wall. A common target is having the center of the screen near seated eye level, roughly 40–45 inches from the floor for a living room. Check for glare from windows and make sure the screen will clear furniture.
- 3
Find and mark the studs
Scan the area with a stud finder and mark both edges of each stud with painter's tape. Confirm by driving a thin finish nail or small drill bit where the mount will cover the hole. Studs in most US homes are 16 inches apart on center, sometimes 24.
- 4
Check for wires and pipes
Look for outlets, switches or plumbing fixtures above or below the spot, since wires and pipes usually run vertically from them. Many stud finders have an AC detection mode — use it. Move the mount if anything is in the drilling path.
- 5
Mark the wall plate position
Hold the wall plate on the wall at the height you chose, centered on the studs, and set a level on top. Mark the lag bolt holes through the plate's slots, placing them in the center of the studs.
- 6
Drill pilot holes
Drill pilot holes at each mark using the bit size the mount instructions specify, usually about 2 1/2 to 3 inches deep for wood studs. You should feel firm resistance and see wood shavings — if the bit suddenly goes slack, you've missed the stud.
- 7
Bolt the wall plate to the studs
Hold the plate in place, slip washers on the lag bolts and drive them with a socket wrench. Tighten until the plate is snug against the wall and doesn't move, but stop before the washer crushes into the drywall. Re-check level before the final turn.
- 8
Attach the brackets to the TV
Lay the TV face-down on a blanket on a table. Thread the screws from the mount kit into the VESA holes by hand first to find the right length — they should thread fully without bottoming out. Use spacers if the back of the TV is curved or has bumps. Tighten snugly; don't overtighten into the TV's plastic.
- 9
Plan and route the cables
Decide how cables will reach the TV before it goes up. For a clean look, use a code-compliant in-wall power kit with recessed boxes, or run cables in a surface raceway. Never push a regular power cord or extension cord through the wall cavity.
- 10
Hang the TV and lock it
With a helper, lift the TV and hook the brackets onto the wall plate. Engage the safety locks or tighten the security screws the instructions describe — this keeps the TV from being knocked off the plate. Fine-tune tilt and level using the mount's adjustments.
- 11
Test the mount
Gently pull down and outward on the bottom of the TV to make sure it's secure. For articulating mounts, extend and swivel the arm through its full range to make sure the cables have enough slack and nothing pinches.
Common mistakes
- Mounting into drywall alone with plastic anchors — drywall can't carry a TV's weight, especially on an articulating arm.
- Hanging the TV too high, such as over a tall fireplace, which leads to neck strain and heat exposure.
- Running a standard power cord or extension cord inside the wall, which violates electrical codes and is a fire hazard.
- Using screws that are too long in the VESA holes, which can damage the TV's internals.
- Skipping the safety lock on the TV brackets so the TV can be bumped off the wall plate.
Frequently asked questions
Can you mount a TV without studs?
Only light TVs on fixed or low-profile mounts, and only with heavy-duty anchors rated well above the TV's weight, such as metal toggle bolts. For articulating mounts or larger TVs, use studs. Some mounts are wide enough to reach studs that aren't centered on the wall.
How high should a TV be mounted?
A good starting point is the center of the screen at seated eye level, often around 40–45 inches off the floor in a living room. In a bedroom where you watch reclined, a little higher and tilted down is more comfortable.
What's the difference between fixed, tilting and full-motion mounts?
Fixed mounts hold the TV closest to the wall. Tilting mounts angle the screen down to cut glare when it's mounted higher. Full-motion or articulating mounts swing out and swivel, which helps in corners but puts much more load on the studs. Our TV mount roundup compares each type.
Can I mount a TV on brick or concrete?
Yes. Drill into the solid brick or block rather than the mortar joint using a hammer drill and masonry bit, then use the masonry anchors or sleeve anchors the mount maker specifies. Some mounts include concrete hardware; many don't.
Is it safe to hide TV cables in the wall?
Low-voltage cables like HDMI are fine in the wall if they are rated for in-wall use (look for CL2 or CL3 on the jacket). Power is different: use a code-compliant in-wall power kit or have an electrician install an outlet behind the TV.
Related guides
- GuideHow to Install GuttersInstall sectional gutters on a one-story home: measure the run, snap a slope line, place downspouts, space the hangers, seal seams and end caps, and stay safe on the ladder.
- GuideHow to Replace a Garbage DisposalSwap out a dead or leaking garbage disposal in an afternoon: cut the power, remove the old unit, wire the new one, seat the mounting ring and leak-test everything.
- GuideHow to Install a BathtubAn honest walkthrough of installing an alcove bathtub: removing the old tub, checking the subfloor, setting a ledger and mortar bed, connecting the drain and overflow, and waterproofing.