Skip to content

Cleaning

How to Clean Hardwood Floors Without Damaging Them

Identify your floor's finish, then clean it the right way — dry dusting, damp (not wet) mopping with a pH-neutral cleaner, and removing scuffs and spots — plus what flooring makers say to avoid.

Hardwood floors are tougher than they look, but they have two weaknesses: grit and water. Sand and dirt scratch the finish every time someone walks over them, and too much water seeps into seams, swelling the boards and clouding the finish. Good hardwood cleaning is mostly about removing grit often and using as little water as possible.

The other piece is knowing your finish. Most floors installed in recent decades have a surface finish such as polyurethane, which handles a damp mop and a pH-neutral cleaner well. Oiled and waxed floors need different care, so figure out what you have before choosing products.

Identify your finish first

Test or clueSurface-sealed (polyurethane, aluminum oxide factory finish)Oiled or waxed
Water drop in a hidden spotBeads up on the surfaceSoaks in and darkens the wood
Look and feelClear, even layer on top; can be satin to glossyLow sheen; wood feels more natural
Mineral spirits on a cotton ballNo residueWax leaves a yellowish or brown smudge
ScratchesUsually white or gray in the finish layerUsually in the wood itself; can often be touched up
Everyday cleaningDry dust, then damp mop with pH-neutral cleanerDry dust; maker-approved products only

If the water soaks in on a floor that should be sealed, the finish may simply be worn through in that area, which is a sign it's due for a professional screen and recoat.

What to avoid on most finishes

Flooring makers and finish manufacturers agree on a short list of things to skip:

  • Steam mops — heat and moisture can damage wood and finish.
  • Vinegar and other acidic or ammonia-based cleaners — they can dull polyurethane over time.
  • Oil soaps, waxes and furniture polish on sealed floors — they leave a film that gets slippery and can keep a new coat of finish from bonding later.
  • Wet mops and buckets of water — standing water is the enemy.

A microfiber mop with washable pads makes the whole routine easier: one dry pad for dusting, one barely damp pad for cleaning. Pair it with a pH-neutral hardwood cleaner that matches your finish.

Engineered hardwood and laminate

Engineered hardwood has a real wood top layer and is cleaned the same way as solid hardwood. Laminate looks similar but is a different product with its own instructions — it's also sensitive to water at the seams, so follow the laminate maker's guidance.

Step by step

  1. 1

    Identify your floor's finish

    Most modern hardwood has a surface finish such as polyurethane. Older or specialty floors may be oiled or waxed. Use the tests in the table below in an out-of-the-way spot, and check with the flooring maker or installer if you can — their cleaning instructions come first.

  2. 2

    Clear the floor and pick up grit

    Move small rugs, chairs and clutter. Sand and grit act like sandpaper underfoot, so removing them is the most important part of cleaning hardwood.

  3. 3

    Dry mop or vacuum

    Go over the floor with a dry microfiber mop, or vacuum using the hard floor setting with the beater bar turned off so the brush doesn't scratch the finish. Follow the direction of the boards and get along the baseboards.

  4. 4

    Damp mop with a pH-neutral cleaner (surface-sealed floors)

    Mist cleaner onto a small area or onto the mop pad, or wring a mop until it's barely damp. The floor should dry within a minute or two. Work in sections, moving with the grain, and swap to a clean pad when the first one gets dirty.

  5. 5

    Use the right product for oiled or waxed floors

    Oiled and waxed floors are more sensitive to water. Dust and vacuum them regularly, and use only the cleaner or maintenance product their finish maker recommends rather than a general mop-on cleaner.

  6. 6

    Wipe up spills and spots

    Blot spills right away with a soft cloth. For sticky spots, mist a little hardwood cleaner on a cloth and rub gently. For gum or candle wax, harden it with ice in a bag, then lift it off carefully with a plastic card.

  7. 7

    Remove scuff marks

    Rub black heel or shoe scuffs with a clean tennis ball or a dry microfiber cloth. If a mark remains, try a small amount of hardwood cleaner on a cloth. Avoid abrasive powders and scrub pads.

  8. 8

    Protect the floor

    Put felt pads under chair and table legs, use doormats inside and out, and keep pets' nails trimmed. Use rugs with backings labeled safe for hardwood, since some rubber backings can discolor finishes.

Common mistakes

  • Wet mopping or letting water stand on the floor, which can swell boards and damage the finish.
  • Using a steam mop on hardwood — many flooring makers warn that heat and moisture can harm the wood and finish and may void the warranty.
  • Cleaning with vinegar, which is acidic and can dull a finish over time.
  • Using oil soaps, waxes or furniture polish on polyurethane floors, which leave residue and can make future recoating difficult.
  • Vacuuming with the beater bar spinning, which can scratch the finish.

Frequently asked questions

What is the best thing to clean hardwood floors with?

For most surface-sealed floors, a pH-neutral cleaner made for hardwood, applied with a barely damp microfiber mop, is the safest choice. Always check your flooring maker's recommendations — they may specify a product, and using something else can affect your warranty.

Can I use vinegar on hardwood floors?

Many flooring manufacturers advise against it. Vinegar is acidic, and repeated use can dull a polyurethane finish. A pH-neutral hardwood cleaner is a safer everyday option.

Are steam mops safe for hardwood floors?

Most hardwood flooring makers say no. Steam pushes heat and moisture into seams and can cause cupping, finish damage and discoloration. Some steam mop makers say their products are safe for sealed floors, but follow your floor's instructions first.

How often should I clean hardwood floors?

Dry mop or vacuum high-traffic areas a few times a week, or whenever you see grit. Damp mop every week or two, or as needed in kitchens and entryways. Wipe up spills right away.

How do I tell if my floor is sealed or waxed?

Put a drop of water on the floor in a hidden spot. If it beads up, the floor likely has an intact surface finish. If it soaks in and darkens the wood, it's probably oiled, waxed or worn. For a wax check, rub a spot gently with a cotton ball dampened with mineral spirits in a ventilated room — a yellowish or brown smudge suggests wax.