Home Repair
How to Patch a Hole in Drywall
Repair drywall holes of any size — spackle for nail holes, a mesh patch for small holes, and a cut-in piece with backing for big ones — then mud, sand and prime so the patch disappears.
Doorknobs, furniture moves and old wall anchors all leave holes in drywall. The repair is the same idea at every size — fill or bridge the hole, cover it with thin layers of compound, then sand and prime so it blends in. What changes is how you bridge it.
This is an easy job that mostly takes patience. The actual work is an hour or two; the rest is waiting for each coat to dry.
Choose the repair by hole size
| Hole size | Example | Repair |
|---|---|---|
| Under 1/2 inch | Nail holes, picture-hanger holes | Lightweight spackle, one or two coats |
| 1/2 inch to about 6 inches | Wall anchor pulled out, small doorknob hole | Self-adhesive mesh patch plus joint compound |
| Over about 6 inches | Large doorknob hole, accidental damage | Cut-in drywall patch with wood backing, taped seams |
| Long crack along a seam | Settling, popped tape | Remove loose tape, re-tape and mud |
| Popped nail heads | Bumps along a stud | Drive a drywall screw beside it, reset the nail, spackle |
Getting the patch to vanish
The secret is width, not thickness. Each coat should spread a few inches past the one before it, so the patch tapers gently into the wall. Hold a flashlight flat against the wall after sanding — the low angle shows any ridges or dips that will show through the paint.
A patch kit covers most small repairs. For bigger ones, wide drywall knives make it far easier to feather the edges smooth. A stud finder helps you locate framing and detect wiring before you cut.
If the hole came from a TV mount or heavy shelf that pulled out, re-hang it into studs rather than anchors — see how to install a TV wall mount.
Step by step
- 1
Size up the hole
Nail and screw holes need only spackle. Holes up to about 6 inches across can take a self-adhesive mesh patch. Anything bigger, or any hole with crumbling edges, gets a cut-in piece of new drywall with wood backing.
- 2
Check for wires and pipes
Before you cut, scan the area with a stud finder that detects live AC wiring, and shine a flashlight into the hole to look inside the wall. Outlets, switches and fixtures nearby usually mean wires run up or down from them. Make cuts shallow until you're sure, and shut off the circuit if you'll be working near a wire.
- 3
Fill nail holes and small dents
Press lightweight spackle into the hole with a putty knife, scrape it flush, and let it dry. A second thin coat fixes any shrinkage. Sand lightly with a fine sponge.
- 4
Apply a mesh patch to small holes
Trim any loose paper around the hole. Center the self-adhesive patch over it and press it flat. Spread a thin coat of joint compound over the patch, feathering it several inches past the edges with a 6-inch knife.
- 5
Cut out a large hole to a clean square
Draw a square or rectangle around the damage with a straightedge, reaching past any cracked or loose areas. Cut it out with a jab saw, keeping the blade shallow. If one side lands on a stud, cut to the middle of the stud so the patch has something to screw to.
- 6
Add backing strips
Cut two wood strips about 4 inches longer than the opening. Slide each one inside the wall behind an edge of the hole and hold it so it spans the opening halfway behind the drywall. Fasten each strip with a drywall screw through the wall above and below the hole, sinking the heads just below the surface.
- 7
Screw in the new piece
Cut a drywall patch to fit the opening with about an eighth-inch gap all around. Set it in place and drive screws through it into the backing strips, slightly dimpling the paper without tearing it.
- 8
Tape and mud the seams
Spread a thin bed of joint compound along each seam, press in paper tape and smooth it out with a 6-inch knife, squeezing excess mud from underneath. Cover the screw heads too. Let it dry completely, usually overnight.
- 9
Feather on two more thin coats
Apply a second coat with a wider knife, spreading it a few inches beyond the first. Let it dry, then add a third coat wider still. Several thin coats look better and sand easier than one thick one.
- 10
Sand, prime and paint
Sand lightly until the edges blend into the wall and you can't feel a ridge with your hand. Wipe off the dust, prime the patched area so the paint doesn't look dull, then paint. For best results, paint the whole wall or out to a corner.
Common mistakes
- Cutting into a wall without checking for wires, pipes or ductwork behind it.
- Applying one thick coat of compound, which cracks, shrinks and takes far longer to sand.
- Skipping the primer, so the patch shows through the paint as a dull or shiny spot.
- Driving screws so deep they tear the paper face, which weakens the hold.
- Over-sanding and scuffing the paper on the surrounding wall.
Frequently asked questions
Can I just use spackle on a bigger hole?
Not well. Spackle is meant for small holes and dents. On anything larger than a coin, it sags, cracks or falls into the wall. Use a mesh patch or a new piece of drywall with backing.
How long does joint compound take to dry?
Premixed compound usually needs several hours to overnight per coat, longer in humid or cold rooms. Setting-type compound (sold as a powder with a time on the bag, like 20 or 45 minutes) hardens chemically and lets you recoat sooner.
What's the difference between spackle and joint compound?
Spackle is a thicker, quick-drying filler for small holes. Joint compound is smoother, spreads wider and is used with tape for seams and larger patches. For anything with tape, use joint compound.
How do I match the texture on a textured wall?
Spray texture is sold in cans for orange peel and knockdown finishes. Practice on cardboard first, then apply it after sanding and before priming. Matching a heavy texture exactly can take a few tries.
Is old drywall dust dangerous?
Drywall dust irritates lungs, so wear a mask. If your home was built before 1978, the paint may contain lead — don't sand it without testing first. Older textured ceilings and some joint compounds can contain asbestos, so have suspect material tested before disturbing it.
Related guides
- GuideHow to Install a TV Wall MountMount a TV securely on drywall, plaster or brick: match the VESA pattern, pick the right height, find studs, drive lag bolts, level the bracket and hide the cables safely.
- GuideHow to Replace a Light SwitchSwap out a worn or broken wall switch safely: turn off the breaker and verify it's dead, tell a single-pole from a 3-way switch, connect the ground, and know when to call an electrician.
- GuideHow to Install a Ceiling FanReplace a ceiling light with a fan: confirm a fan-rated electrical box (or add a brace bar), choose a downrod or flush mount, wire black, white, ground and blue, then balance the blades.