Skip to content

Home Repair

How to Install Gutters

Install sectional gutters on a one-story home: measure the run, snap a slope line, place downspouts, space the hangers, seal seams and end caps, and stay safe on the ladder.

Gutters do one job — move roof water away from your siding and foundation — but they need to do it on every inch of the roof edge, in every storm. A gutter that's hung level, sags between hangers or dumps water at the foundation can cause more damage than having no gutter at all.

This guide covers sectional aluminum or vinyl gutters on a one-story house, which is a realistic weekend project for a careful DIYer with a helper. The principles (slope, downspout placement, hanger spacing and sealing) apply to any gutter system, but always follow the instructions for the specific system you buy.

Planning the layout

Sketch the house from above and mark every roof edge that sheds water. For each run, note the length, the corners, and where downspouts will go. Good downspout spots are corners and low points where water can flow away from the house — not next to walkways, driveways or window wells.

Run lengthTypical layout
Up to about 35–40 feetSlope one way to a single downspout at the low end
Longer than about 40 feetPeak in the middle, slope both ways to a downspout at each end
Valleys or very large roof sectionsConsider an extra downspout or larger gutter size where water concentrates

Put a ladder with a standoff on your list before anything else, and pick a gutter sealant that matches your gutter material. If trees overhang the roof, gutter guards can save a lot of ladder time later.

Related jobs

Working your way around the outside of the house? Another common fix is a garage door that won't close — usually a dirty or misaligned safety sensor.

Step by step

  1. 1

    Inspect the fascia and measure the runs

    Walk the house and check the fascia boards for rot or soft spots — gutters are only as strong as the wood they hang from. Replace bad sections first. Then measure each roof edge that needs a gutter and note where corners fall, adding a little extra for overlaps.

  2. 2

    Plan the downspouts

    Decide where water will exit. Place downspouts at the corners or low ends of runs, where water can drain away from the foundation onto ground that slopes away from the house. A common rule of thumb is one downspout for every 30–40 feet of gutter; runs longer than about 40 feet usually slope down from the middle to a downspout at each end.

  3. 3

    Snap the slope line

    At the high end of the run, make a mark on the fascia about 1 1/4 inches below the roof edge or drip edge. At the downspout end, measure down an additional amount for slope — commonly about 1/4 inch per 10 feet of run — and mark it. Snap a chalk line between the marks. Check it with a line level so the fall is consistent.

  4. 4

    Cut and assemble the sections on the ground

    Measure and cut gutter sections with a hacksaw or snips, then attach end caps, corners and connectors on the ground where it's safer. Overlap joints in the direction water flows (upstream piece inside the downstream piece), fasten with rivets or screws, and seal the inside of every seam and end cap with gutter sealant.

  5. 5

    Cut the downspout outlet hole

    Mark the downspout outlet position on the gutter bottom, then cut the opening with snips or a hole saw sized for the outlet. Insert the outlet from inside the gutter, seal around its flange, and rivet or screw it in place.

  6. 6

    Install the hangers along the chalk line

    Hidden hangers snap inside the gutter's front lip and screw through the back into the fascia. Space them about every 24 inches, or closer — around 16 to 24 inches — in areas with heavy snow, ice or tree debris. Follow the gutter manufacturer's spacing if it differs.

  7. 7

    Lift and fasten the gutter

    With a helper on a second ladder, lift the assembled section into position with its back edge on the chalk line. Drive the hanger screws into the fascia (and into the rafter tails behind it where possible). Long sections are floppy; support them at several points as you go.

  8. 8

    Join sections and corners in place

    Where pieces meet on the house, overlap or use the connector designed for your system, fasten, and seal the seam from the inside. Make sure the slope carries through corners and no joint sits higher than the gutter ahead of it.

  9. 9

    Attach the downspouts

    Fit an elbow to the outlet, then run elbows and downspout sections down to the ground, with the crimped end of each upper piece fitting inside the piece below it so water can't leak out. Secure downspouts to the wall with straps every 6–10 feet or as the system recommends, and add an elbow and extension at the bottom to carry water several feet from the foundation.

  10. 10

    Test with a hose

    Run a garden hose into the high end of each gutter. Water should flow steadily to the downspout without pooling. Check every seam for drips and add sealant from the inside where needed. Let sealant cure per its label before heavy rain if you can.

Common mistakes

  • Hanging gutters perfectly level, so water sits in them, or with too much pitch, which looks crooked and overflows at the downspout end.
  • Overlapping seams against the flow of water, which pushes water out through the joint.
  • Spacing hangers too far apart, so the gutter sags under snow, ice or debris.
  • Ending downspouts right next to the foundation instead of carrying water several feet away.
  • Hanging gutters on rotten fascia boards that pull loose in the first big storm.
  • Overreaching from the ladder instead of climbing down and moving it.

Frequently asked questions

How much slope should gutters have?

A common guideline is about 1/4 inch of fall for every 10 feet of gutter, toward the downspout. Some installers use up to about 1/2 inch per 10 feet. Check your gutter manufacturer's recommendation.

How far apart should gutter hangers be?

Roughly every 24 inches in most climates, and closer — around 16 to 24 inches — where heavy snow and ice are common. Always place a hanger near each end and near each seam.

Should I install seamless or sectional gutters?

Sectional gutters are sold in fixed lengths and are the practical DIY option. Seamless gutters are formed on-site from a coil by a machine, so they have joints only at corners and fewer places to leak — but that requires an installer with the equipment.

What size gutters do I need?

5-inch K-style gutters with 2x3-inch downspouts suit many homes. Larger or steeper roofs and areas with heavy rainfall often need 6-inch gutters and 3x4-inch downspouts. A local installer or the gutter maker's sizing chart can confirm.

Do I need gutter guards?

Not always, but they can reduce cleaning if you have trees nearby. Guards vary in how well they shed pine needles versus leaves. See our gutter guard roundup for the main styles.