Home Repair
How to Reset a Garbage Disposal
Get a dead or humming garbage disposal running again: cut the power, free a jam with a hex key, press the red reset button and check the breaker — plus what each symptom means.
A garbage disposal that suddenly stops working is rarely broken. Most of the time it has jammed on something it shouldn't have eaten, or its built-in overload protector has shut the motor off to keep it from burning out. Both problems take a few minutes and a hex key to fix.
Before you call anyone, work through the steps below. They fix the large majority of dead or humming disposals.
What the symptom tells you
Listen to the disposal when you flip the switch. The sound (or silence) narrows down the problem quickly.
| Symptom | Likely cause | What to do |
|---|---|---|
| Hums but doesn't spin | Jammed grinding plate | Power off, free it with a hex key from below, then press reset |
| Completely silent | Tripped reset button, breaker or GFCI outlet, or a bad switch | Press the red reset button; check the breaker and any GFCI outlet |
| Runs a few seconds, then stops | Motor overheating or overloaded | Clear the jam, let it cool 15 minutes, reset, and feed it less at once |
| Spins but drains slowly | Clog in the drain line past the disposal | See our guide to unclogging a drain |
| Loud grinding or rattling | Hard object (metal, glass, pit) in the chamber | Power off and remove it with tongs |
| Leaks from the top near the sink | Loose sink flange or worn putty | Reseat the flange and mounting ring |
| Leaks from the side | Loose dishwasher hose or discharge tube gasket | Tighten the clamp or replace the gasket |
| Leaks from the bottom of the housing | Internal seal failure | The unit needs replacing |
When resetting isn't enough
If the plate spins freely by hand but the motor still only hums, or the reset button trips the moment you turn it on with nothing inside, the motor itself is failing. A leak from the bottom of the disposal body is also a sign of internal seal failure, and that can't be repaired in place.
In those cases replacement is the answer. Our step-by-step guide to replacing a garbage disposal covers removing the old unit, wiring the new one and leak-testing, and our garbage disposal roundup compares horsepower, noise and warranties.
Keeping it from jamming again
Run cold water before, during and for a few seconds after grinding. Feed food in gradually rather than all at once. Keep out the usual troublemakers: grease, bones, fruit pits, eggshells in quantity, coffee grounds in bulk, and stringy or starchy scraps like celery, corn husks, potato peels and pasta. And keep a hex key in the sink cabinet — the next jam will take two minutes.
Step by step
- 1
Turn off the disposal and cut the power
Flip the wall switch off, then unplug the disposal under the sink. If it's hardwired with no plug, switch off its circuit at the breaker panel. Don't skip this — a jam can free itself and the blades start turning the moment power returns.
- 2
Look for the obstruction
Shine a flashlight down the drain opening. If you can see an object such as a bottle cap, fruit pit or piece of silverware, pull it out with tongs or pliers. Never reach into the disposal with your hand.
- 3
Free the jam from underneath
Find the small hex socket in the center of the bottom of the disposal. Insert a 1/4-inch hex key or the disposal wrench and work it back and forth until it turns a full circle freely. That spins the grinding plate and breaks up whatever was stuck.
- 4
Remove anything that came loose
Look down the drain again with the flashlight and remove any freed debris with tongs. Turn the hex key a few more times to confirm the plate spins easily.
- 5
Let the motor cool
If the disposal was humming or shut itself off, give the motor about 10 to 15 minutes to cool. The thermal overload won't reset while the motor is still hot.
- 6
Press the red reset button
Find the small red (sometimes black) button on the bottom of the disposal, usually near the hex socket or the power cord. If it has popped out, press it firmly until it clicks and stays in.
- 7
Restore power and test
Plug the disposal back in or turn the breaker on. Run cold water into the sink and flip the switch. It should start right away and run smoothly. Keep the water running while it grinds.
- 8
Check the breaker and outlet if it's still silent
If nothing happens, look for a tripped breaker in the panel and reset it. If the disposal plugs into an outlet, check whether that outlet is on a GFCI that has tripped (press its reset button), and confirm the wall switch actually controls that outlet.
Common mistakes
- Putting a hand in the disposal to clear a jam, even with the switch off.
- Pressing the reset button repeatedly without clearing the jam, which just trips the motor again.
- Running the disposal without cold water, which lets debris and grease pack into the drain.
- Using chemical drain cleaners in a disposal, which can damage seals and splash back during repairs.
- Ignoring water leaking from the bottom of the housing — that usually means the unit is finished.
Frequently asked questions
Where is the reset button on a garbage disposal?
On the bottom of the unit under the sink. It's a small red or black button, often near the center hex socket or where the cord enters. When it has tripped, it sticks out slightly.
Why does my disposal hum but not spin?
Something is jamming the grinding plate, so the motor gets power but can't turn. Cut the power, work a 1/4-inch hex key back and forth in the socket on the bottom until it spins freely, remove the debris, then press the reset button.
Why does my garbage disposal keep tripping the reset button?
Usually it's being overloaded — too much food at once, fibrous peels, or not enough water. If it trips even when empty and spinning freely, the motor may be overheating from age and the unit is likely near the end of its life.
Can I use a broom handle to unjam a disposal?
It's a common trick, but the hex socket on the bottom is safer and gives you more leverage. If you do push on the plate from above, use a wooden handle only, with the power off at the breaker or unplugged, and never use your hand.
When should I replace the disposal instead of resetting it?
Replace it if it leaks from the bottom of the housing, hums even when the plate spins freely by hand, keeps tripping when empty, or is more than about 10 to 12 years old and struggling. Our guide to replacing a garbage disposal walks through the swap.
Related guides
- GuideHow to Replace a Garbage DisposalSwap out a dead or leaking garbage disposal in an afternoon: cut the power, remove the old unit, wire the new one, seat the mounting ring and leak-test everything.
- GuideHow to Unclog a DrainClear a slow or stopped sink or tub drain with hot water, a plunger, a drain snake or by cleaning the P-trap — plus what not to pour down it and how to tell when the problem is the main line.
- GuideHow to Install a DishwasherInstall a built-in dishwasher step by step: power (plug-in or hardwired), the water line and elbow, a proper drain loop or air gap, leveling, anchoring and the leak test.