Skip to content

Home Repair

How to Fix a Running Toilet

Find out why your toilet keeps running — flapper, chain, float, fill valve or overflow tube — with a simple food-coloring test, then replace the flapper or fill valve yourself.

A toilet that keeps running, refills on its own, or hisses quietly all night is wasting water — but it's one of the easiest plumbing repairs in the house. Almost every case comes down to five parts inside the tank, and most fixes need nothing more than a new rubber flapper or a quick adjustment.

Start by diagnosing, not buying parts. Ten minutes with food coloring tells you exactly which part is at fault.

Diagnose it by the symptom

What you see or hearLikely causeFix
Food coloring shows up in the bowlFlapper not sealingClean the seat, adjust the chain, or replace the flapper
Water spills into the overflow tubeWater level set too highLower the float
Fill valve hisses and never stops, even at the right levelWorn fill valveReplace the fill valve
Tank refills every few minutes or hoursSlow flapper leak or a siphoning refill tubeLeak test, then check the refill tube
Handle has to be jiggled to stop the flowChain too tight, tangled or catchingAdjust or shorten the chain
Water keeps running with the level below the overflow tubeCracked overflow tube or flush valveReplace the flush valve (tank comes off)

Know your parts

  • Flapper — the rubber seal at the bottom of the tank that lifts when you flush.
  • Chain — links the flush handle to the flapper.
  • Float — a cup around the fill valve or a ball on an arm that tells the valve when to stop.
  • Fill valve — the tall valve on the left that refills the tank.
  • Overflow tube — the open pipe in the middle that keeps the tank from overflowing.

When buying parts, check whether your flush valve opening is 2 or 3 inches across. Our roundups of toilet flappers and fill valves list the common universal sizes. If your toilet is old, cracked, or you're replacing several parts at once, it may make more sense to replace the toilet.

Step by step

  1. 1

    Take the tank lid off and watch

    Set the lid on a towel — it's heavy and breaks easily. Flush and watch the parts work. Note whether water is spilling into the overflow tube or the fill valve is hissing nonstop.

  2. 2

    Run the food-coloring leak test

    Add 10 or so drops of food coloring to the tank water and don't flush for 15–30 minutes. If color shows up in the bowl, water is leaking past the flapper. If the bowl stays clear but the toilet still runs, the problem is the water level or the fill valve.

  3. 3

    Check the chain

    The chain from the flush handle to the flapper should have about a half inch of slack when the flapper is closed. Too tight and the flapper can't seal; too loose and it can tangle under the flapper. Move the clip one or two links and test again.

  4. 4

    Set the water level

    With the tank full, the water should stop about an inch below the top of the overflow tube, or at the line marked inside the tank. On a float-cup fill valve, squeeze the clip or turn the adjustment screw to lower the cup. On an older ball float, bend the arm down slightly or turn the screw on top of the valve.

  5. 5

    Check the refill tube

    The small tube from the fill valve should clip to the overflow tube and aim into it, not be pushed down inside. If it sits below the water line, it can siphon water out of the tank and keep the valve cycling.

  6. 6

    Shut off the water and drain the tank

    Turn the supply valve behind the toilet clockwise until it stops. Flush and hold the handle down to empty the tank, then sponge out what's left.

  7. 7

    Replace the flapper

    Unhook the old flapper's ears from the pegs on the overflow tube (or slide its ring off), and unclip the chain. Wipe the flush valve seat with a cloth; if it's rough, rub it gently with fine sandpaper or a scouring pad. Install the new flapper, attach the chain with a little slack, and trim any extra chain.

  8. 8

    Replace the fill valve if it won't shut off

    With the tank empty, put a towel down and unscrew the supply line from the bottom of the tank. Remove the plastic locknut under the tank and lift out the old valve. Set the new valve's height per its instructions, so the top sits at least an inch above the overflow tube, tighten the locknut by hand plus a quarter turn, reconnect the supply line and clip on the refill tube.

  9. 9

    Turn the water on and test

    Open the supply valve slowly and let the tank fill. Adjust the water level, flush a few times, and check under the tank for drips. Repeat the food-coloring test an hour later to confirm the seal.

Common mistakes

  • Buying a 2-inch flapper for a toilet with a 3-inch flush valve, or the reverse. Check the opening size or the toilet model first.
  • Pushing the refill tube down into the overflow tube, which siphons water out of the tank.
  • Overtightening the plastic locknut or supply nut and cracking the tank or the fitting.
  • Leaving the chain so loose it gets trapped under the new flapper.
  • Setting the water level above the overflow tube, so water constantly spills down it.

Frequently asked questions

Why does my toilet run for a few seconds every so often?

That's called phantom flushing. Water is slowly leaking from the tank into the bowl, usually past a worn flapper, until the fill valve tops it back up. The food-coloring test will confirm it.

How much water can a running toilet waste?

It varies widely. A slow flapper leak may waste a little each day, while a fill valve that never shuts off can send a large amount of water down the overflow tube. Either way, it shows up on your water bill, so it's worth fixing promptly.

Can I just adjust the flapper instead of replacing it?

Sometimes. If the flapper is clean and flexible, fixing the chain or cleaning the valve seat may be enough. If it's warped, stiff, slimy or crumbly to the touch, replace it — flappers are inexpensive and wear out over the years.

Do I need to buy a flapper that matches my toilet brand?

Many toilets use a universal 2-inch or 3-inch flapper, but some models use brand-specific seals or canister valves. Look for a model number stamped inside the tank, or bring the old part to the store.

My toilet still runs after a new flapper. What now?

Check the chain length and water level again, then look at the flush valve seat for chips or mineral buildup. If the fill valve itself keeps hissing, replace it. A cracked overflow tube means the whole flush valve needs replacing, which requires removing the tank.