Skip to content

Home Repair

How to Fix a Garage Door That Won't Close

Most garage doors that refuse to close have a blocked or misaligned safety sensor, a locked wall control or a limit setting off. Here's how to find the cause — and what to leave to a pro.

A garage door that opens fine but refuses to close is frustrating, but it's usually the opener doing exactly what it's designed to do: refusing to lower a heavy door when it thinks something is in the way. Residential openers sold in the US since 1993 have been required to include extra entrapment protection, usually photo-eye sensors, and that's what's stopping you.

Nine times out of ten, the fix is cleaning or realigning the two little sensors at the bottom of the door. The rest of the time it's a lock setting, a limit adjustment, or something in the track.

Symptom and likely cause

What the door doesLikely causeWhat to try
Won't move down at all; opener light blinksSafety sensors blocked or misalignedClear the path, clean the lenses, realign until both lights are steady
Starts down, then reverses partwaySensor beam interrupted, or door binding in the trackCheck sensors; inspect tracks and rollers for damage
Touches the floor, then reversesClose limit set too farAdjust the down limit slightly per the opener manual
Stops a few inches above the floorClose limit set too shortAdjust the down limit slightly the other way
Closes only when the wall button is held downSensors misaligned or faulty wiringRealign; check sensor wires for damage
Remote does nothing, wall button worksLock or vacation mode, or dead remote batteryTurn off lock mode; replace the battery
Opener hums, door doesn't move or feels very heavyBroken spring or cableStop. Don't force it — call a garage door pro
Door is crooked or a cable hangs looseCable off its drum or brokenStop. Leave the door alone and call a pro

Safety sensors explained

The two photo-eye sensors near the floor send an invisible beam across the opening. If the beam is broken while the door is closing, the opener stops and reverses. One sensor sends, one receives, and each has an indicator light.

The sensors get knocked out of line by bikes, brooms and car bumpers, and their lenses collect dust and cobwebs. Low sun shining straight into the receiving sensor can also blind it at certain times of day — if your door fails only in the late afternoon, that's the clue. Cleaning and aiming them is usually all it takes.

Don't skip the reversal test

Any time you adjust the sensors, the limits or the force settings, test the safety features before using the door normally. Place a 2x4 flat on the floor where the door lands and close it — the door should reverse after contact. Then close it again and pass something through the sensor beam — it should reverse immediately. If your opener's manual describes a different test object, use that one. A door that doesn't pass shouldn't be used with the opener until it's corrected.

Step by step

  1. 1

    Clear the doorway and the tracks

    Look along the floor and both vertical tracks for anything in the way: a toy, a trash can lid, leaves, a hose, or a tool leaning near the track. Even a small object in the sensor beam or track will stop the door.

  2. 2

    Check the safety sensor lights

    Find the two small photo-eye sensors on either side of the door, a few inches above the floor. Each has an indicator light. On most openers both glow steadily when aligned; if one is off or blinking, the beam isn't connecting.

  3. 3

    Clean the sensor lenses

    Wipe both lenses with a soft dry cloth. Dust, cobwebs, spider eggs and condensation are common culprits. Make sure no direct sunlight is shining into the receiving sensor — glare can blind it at certain times of day.

  4. 4

    Realign the sensors

    Loosen the wing nut or screw on the misaligned sensor's bracket, aim it directly at the other sensor until its light glows steady, and retighten. A level or a taut string between them helps get both at the same height. Check that the wires to each sensor aren't cut or pulled loose.

  5. 5

    Check the wall control and remote

    Many wall controls have a lock or vacation button that disables remotes; if the remote won't work but the wall button does, turn the lock off. If the remote alone fails, replace its battery. If neither works, check that the opener is plugged in and its outlet has power.

  6. 6

    Test with the wall button held down

    On many openers, pressing and holding the wall button closes the door even when the sensors aren't aligned. If that works, the problem is almost certainly the sensors. Watch the door the whole way and let go if anything is in the path.

  7. 7

    Adjust the close limit if the door reverses at the floor

    If the door touches the floor and immediately goes back up, or stops a few inches short, the close limit is off. Using your opener's manual, adjust the down-limit setting (a dial, screw or button sequence) a small amount at a time and test after each change.

  8. 8

    Inspect the tracks and rollers

    With the door closed and the opener unplugged, look for bent track sections, loose track brackets, or cracked and wobbly rollers. Tighten loose bracket bolts that hold the track to the wall. Lubricate rollers and hinges lightly with garage door lubricant; wipe the tracks clean rather than greasing them.

  9. 9

    Use the manual release if you need to close it now

    If you must close the door before it's fixed, pull the red emergency release cord to disconnect the opener, then lower the door by hand slowly. Be careful: if a spring is broken, the door will be very heavy and can drop. Reconnect the trolley by running the opener or following its manual.

  10. 10

    Run the safety reversal test

    After any adjustment, lay a 2x4 flat on the floor in the door's path (or a roll of paper towels for opener models whose manual specifies it) and close the door. It must reverse when it touches the object. Then wave something through the sensor beam while it closes — it should reverse. If either test fails, don't use the opener until it's fixed.

Common mistakes

  • Adjusting, loosening or trying to replace torsion springs or lift cables — these are under extreme tension and can cause serious injury.
  • Holding the wall button to close the door every day instead of fixing the sensors, which defeats a key safety feature.
  • Increasing the force setting to push past a sticky track, so the door may not reverse on a person or pet.
  • Pulling the emergency release with the door open when a spring might be broken, letting the door fall.
  • Greasing the tracks, which collects dirt and makes rollers skid instead of roll.

Frequently asked questions

Why does my garage door go down then back up?

The opener thinks something is in the way. Common reasons are a blocked or misaligned safety sensor, the close limit set too far so the door hits the floor and reverses, or the door binding in the track. Check the sensor lights first, then the limit setting in your opener's manual.

How do I know if my garage door sensors are misaligned?

Look at the indicator lights on both sensors. On most brands, one or both lights will be off or blinking when the beam is broken or misaligned. Some openers also flash the main light or show a code on the wall control.

Can I fix a broken garage door spring myself?

No. Torsion springs and the cables attached to them hold enormous stored energy, and releasing it incorrectly can cause severe injuries. A broken spring often shows up as a gap in the coil above the door or a door that feels extremely heavy. Leave the door closed if possible and call a garage door professional.

Why does my remote not work but the wall button does?

The remote battery may be dead, the wall control may be in lock or vacation mode, or the remote may need to be reprogrammed to the opener. Try the lock button first, then a fresh battery, then your opener's programming steps.

When should I replace the garage door opener?

Consider replacing it if the motor hums but doesn't move a properly balanced door, the logic board has failed, or it's an older model without modern safety sensors. Our garage door opener roundup compares drive types and features.