Skip to content

Cleaning

How to Clean a Keurig (and Descale It)

Clean your Keurig the right way: wash the drip tray and K-cup holder, clear the exit needle, refresh the reservoir, descale, and swap the water filter.

A Keurig makes coffee fast, but it also hides a surprising amount of gunk. Coffee drips pile up in the tray, grounds pack into the exit needle, the reservoir grows a film if water sits too long, and hard-water minerals slowly coat the inside of the brewer. The result is weak coffee, slow brews, half-full cups and, eventually, a machine that won't brew at all.

Cleaning it takes about 20 minutes. Add descaling and rinse brews and you're looking at about an hour, most of it waiting.

What to clean, and how often

Not every part needs attention every week. Here's a simple schedule that keeps most Keurigs brewing well.

PartHow oftenWhat to do
Drip tray and plateEvery few daysEmpty, wash with soapy water, dry
K-cup holder and funnelWeeklyWash; check the exit needle for grounds
Exit and entrance needlesWhen brews slow or grounds appearClear with a straightened paperclip, unplugged
Water reservoirWeeklyWash with soapy water, rinse well, air dry
Outside and under the lidWeeklyWipe with a damp cloth
DescalingEvery 3–6 months, or when the light comes onDescaling solution per your manual, then rinse brews
Water filter cartridgeAbout every 2 months, or per the packageSoak, rinse and replace

If you have hard water, lean toward the shorter end of the descaling range. Chalky white spots on the reservoir or the mug are a good clue.

Descaling solution vs vinegar

Both work by dissolving the calcium and magnesium scale that hard water leaves behind. The difference is mostly in what your manufacturer recommends and how easy each is to rinse out.

  • Descaling solution made for single-serve brewers is what Keurig recommends. It's formulated for the job, it's mostly odorless, and the label gives you exact mixing ratios. Our coffee machine descaler roundup compares common options.
  • White vinegar is cheap and widely used, but it leaves a strong smell and taste that takes extra rinse brews to clear. Some manuals say not to use it, and using something your manual warns against could matter if you ever need a warranty claim.

Whichever you use, the most important step is the rinse: keep running fresh-water brews until the water coming out tastes and smells like nothing.

Some newer Keurig models have a dedicated descale mode or a reminder light. If yours does, follow the on-screen or manual instructions — the steps and number of brews differ by model.

Troubleshooting after a cleaning

Coffee tastes sour or like vinegar. You need more rinse brews. Fill the tank with fresh water and keep going.

Grounds in the cup. The exit needle is still partly clogged, or the pod holder funnel wasn't put back properly. Clear the needle again and reseat the funnel.

The brewer says "add water" with a full tank. Lift the reservoir and reseat it firmly. On some models, a magnet or float in the tank can stick — rinse it and make sure it moves freely.

Brews are still slow. Scale can take more than one cycle to clear on a brewer that's never been descaled. Repeat the descaling process once more, following your manual.

Keeping up with these small jobs every week means you'll rarely face a sluggish brewer — and the same habits work for other machines too. If you also use a pod espresso maker, see our guide on how to clean a Nespresso machine.

Step by step

  1. 1

    Unplug the brewer

    Turn the Keurig off and unplug it before you take anything apart or poke at the needle. Let it cool for a few minutes if you just brewed — the needle area and water in the system get hot.

  2. 2

    Wash the drip tray

    Slide out the drip tray and its plate, empty them, and wash both in warm soapy water. Rinse and dry them before putting them back. Do this every few days, because standing coffee drips turn sour and can grow mold.

  3. 3

    Remove and wash the K-cup holder

    Open the handle and pull the pod holder straight up and out; on most models the funnel underneath pops off too. Wash both in warm soapy water with a small brush to get coffee grounds out of the corners. Many holders are top-rack dishwasher safe, but check your manual first.

  4. 4

    Clear the exit needle

    With the holder removed and the brewer still unplugged, find the exit needle in the bottom of the holder. Push a straightened paperclip up into the needle and move it around gently to dislodge packed grounds. Do the same for the entrance needle on the underside of the lid, keeping your fingers clear of the sharp points.

  5. 5

    Clean the water reservoir

    Lift off the reservoir and lid, remove the filter if there is one, and wash the tank with warm soapy water and a soft sponge. Rinse very well so no soap ends up in your coffee, and let it air dry. Don't scrub the inside with anything abrasive.

  6. 6

    Wipe down the outside

    Wipe the housing, the area around the pod holder, and under the lid with a damp microfiber cloth. Coffee splashes collect around the needle and under the lid, so pay extra attention there. Never submerge the brewer or run it under the tap.

  7. 7

    Descale the brewer

    Empty the reservoir and fill it with descaling solution and water as the product label and your Keurig manual direct. Run cleansing brews (with no pod) into a large ceramic mug, discarding each one, until the brewer says to add water or the tank is nearly empty. Many instructions call for a rest period partway through so the solution can work — follow your model's directions for timing.

  8. 8

    Flush with fresh water

    Rinse the reservoir thoroughly, fill it to the max line with fresh water, and run at least 12 rinse brews (or whatever your manual says) until there's no taste or smell of descaler or vinegar.

  9. 9

    Replace the water filter

    If your model has a charcoal water filter, soak a new cartridge in water for a few minutes, rinse it, and snap it into the holder. Many filters are meant to be replaced about every two months or after a set number of tank refills — your filter's packaging will say.

  10. 10

    Reassemble and run a test brew

    Put the funnel, pod holder, drip tray and reservoir back. Plug the brewer in and run one plain-water brew to make sure the needle is clear and water flows normally before you brew coffee.

Common mistakes

  • Poking at the needle while the brewer is plugged in or still hot.
  • Skipping the rinse brews after descaling, which leaves a sour or chemical taste.
  • Using a paper or plastic cup for cleansing brews — hot descaler can splash or the cup can tip.
  • Running vinegar through a model whose manual says to use only descaling solution.
  • Ignoring the descale light and letting scale build until the brewer only fills half a cup.
  • Leaving water sitting in the reservoir for days, which lets slime and film form.

Frequently asked questions

How often should I clean my Keurig?

Empty and wash the drip tray every few days, wash the pod holder and reservoir about once a week, and clear the exit needle whenever brews get slow or grounds show up in your cup. Descale every three to six months, or when your model's descale light comes on.

Can I descale a Keurig with vinegar?

Many people do, and plain white vinegar does dissolve mineral scale. But Keurig recommends its own descaling solution, and some manuals specifically advise against vinegar. Check your model's manual. If you do use vinegar, rinse with extra fresh-water brews, because the smell lingers.

Why is my Keurig only brewing half a cup?

The usual causes are a clogged exit or entrance needle, mineral scale inside the water lines, or a reservoir that isn't seated properly. Clear the needles with a paperclip first, then descale if that doesn't fix it.

What does the descale light mean?

Some Keurig models track how much water has gone through and turn on a descale reminder when it's time. The light usually stays on until you complete a full descaling cycle as described in your manual.

Do I need to use the water filter?

It's optional on most models. A charcoal filter can improve the taste of tap water, but it doesn't remove all minerals, so you still need to descale. If you use one, replace it on the schedule printed on the package.